Numerical Analysis of a Transtibial Prosthesis Socket Using 3D-Printed Bio-Based PLA
Materials · 28.02.2023 · 16 (5) · 1985
DOI: 10.3390/ma16051985 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.02.2023. Verfasst von Vasja Plesec und 3 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory for Intelligent CAD Systems, Faculty of Mechanical Engineering, University of Maribor, Smetanova ulica 17, 2000 Maribor, Slovenia. Die Arbeit wurde bisher 29-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovenian Research Agency.
Abstract (Originalsprache)
Lower-limb prosthesis design and manufacturing still rely mostly on the workshop process of trial-and-error using expensive unrecyclable composite materials, resulting in time-consuming, material-wasting, and, ultimately, expensive prostheses. Therefore, we investigated the possibility of utilizing Fused Deposition Modeling 3D-printing technology with inexpensive bio-based and bio-degradable Polylactic Acid (PLA) material for prosthesis socket development and manufacturing. The safety and stability of the proposed 3D-printed PLA socket were analyzed using a recently developed generic transtibial numeric model, with boundary conditions of donning and newly developed realistic gait cycle phases of a heel strike and forefoot loading according to ISO 10328. The material properties of the 3D-printed PLA were determined using uniaxial tensile and compression tests on transverse and longitudinal samples. Numerical simulations with all boundary conditions were performed for the 3D-printed PLA and traditional polystyrene check and definitive composite socket. The results showed that the 3D-printed PLA socket withstands the occurring von-Mises stresses of 5.4 MPa and 10.8 MPa under heel strike and push-off gait conditions, respectively. Furthermore, the maximum deformations observed in the 3D-printed PLA socket of 0.74 mm and 2.66 mm were similar to the check socket deformations of 0.67 mm and 2.52 mm during heel strike and push-off, respectively, hence providing the same stability for the amputees. We have shown that an inexpensive, bio-based, and bio-degradable PLA material can be considered for manufacturing the lower-limb prosthesis, resulting in an environmentally friendly and inexpensive solution.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratory for Intelligent CAD Systems, Faculty of Mechanical Engineering, University of Maribor, Smetanova ulica 17, 2000 Maribor, Slovenia.
- Mechanical Engineering Research Institute, Faculty of Mechanical Engineering, University of Maribor, Smetanova ulica 17, 2000 Maribor, Slovenia.
ORCID-Profile: Vasja Plesec, Polona Dobnik-Dubrovski
Förderung
- Slovenian Research Agency
Zitieren
APA
Plesec, V., Humar, J., Dobnik-Dubrovski, P., & Harih, G. (2023). Numerical Analysis of a Transtibial Prosthesis Socket Using 3D-Printed Bio-Based PLA. Materials, 16(5), 1985. https://doi.org/10.3390/ma16051985
Vancouver
Plesec V, Humar J, Dobnik-Dubrovski P, Harih G. Numerical Analysis of a Transtibial Prosthesis Socket Using 3D-Printed Bio-Based PLA. Materials. 2023;16(5):1985. doi:10.3390/ma16051985
BibTeX
@article{Plesec2023,
author = {Plesec, Vasja and Humar, Jani and Dobnik-Dubrovski, Polona and Harih, Gregor},
title = {Numerical Analysis of a Transtibial Prosthesis Socket Using 3D-Printed Bio-Based PLA},
journal = {Materials},
year = {2023},
volume = {16},
number = {5},
pages = {1985},
doi = {10.3390/ma16051985}
}
EUVIMED