EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fractal Analysis on Machined Surface Morphologies of Soft-Brittle KDP Crystals Processed by Micro Ball-End Milling

Qi Liu iD, Jian Cheng, Zhirong Liao iD, Mingyu Liu, Mingjun Chen, Linjie Zhao, Hongqin Lei, Wenyu Ding

Materials · 21.02.2023 · 16 (5) · 1782

DOI: 10.3390/ma16051782 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.02.2023. Verfasst von Qi Liu und 7 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin 150001, China. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Heilongjiang Province, University of Strathclyde.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The micro-defects on KH2PO4 (KDP) optic surfaces are mainly repaired by the micro-milling technique, while it is very easy to introduce brittle cracks on repaired surfaces, as KDP is soft and brittle. To estimate machined surface morphologies, the conventional method is surface roughness, but it fails to distinguish ductile-regime machining from brittle-regime machining directly. To achieve this objective, it is of great significance to explore new evaluation methods to further characterize machined surface morphologies. In this study, the fractal dimension (FD) was introduced to characterize the surface morphologies of soft-brittle KDP crystals machined by micro bell-end milling. The 3D and 2D fractal dimensions of the machined surfaces and their typical cross-sectional contours have been calculated, respectively, based on Box-counting methods, and were further discussed comprehensively by combining the analysis of surface quality and textures. The 3D FD is identified to have a negative correlation with surface roughness (Sa and Sq), meaning the worse the surface quality the smaller the FD. The circumferential 2D FD could quantitively characterize the anisotropy of micro-milled surfaces, which could not be analyzed by surface roughness. Normally, there is obvious symmetry of 2D FD and anisotropy on the micro ball-end milled surfaces generated by ductile-regime machining. However, once the 2D FD is distributed asymmetrically and the anisotropy becomes weaker, the assessed surface contours would be occupied by brittle cracks and fractures, and corresponding machining processes will be in a brittle regime. This fractal analysis would facilitate the accurate and efficient evaluation of the repaired KDP optics by micro-milling.

Schlagwörter

Stichwörter der Autor:innen

KDP crystalbox-counting approachbrittle-to-ductile transitionfractal dimensionmaterial removal modessurface morphology analysis

Autor:innen und Institutionen

  • State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin 150001, China.
  • Centre for Precision Manufacturing, Department of Design Manufacturing & Engineering Management (DMEM), University of Strathclyde, Glasgow G1 1XJ, UK.
  • Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, Nottingham NG8 1BB, UK.
  • School of Engineering, College of Science, University of Lincoln, Lincoln LN6 7TS, UK.

ORCID-Profile: Qi Liu, Zhirong Liao

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Heilongjiang Province
  • University of Strathclyde
  • University of Nottingham

Zitieren

APA

Liu, Q., Cheng, J., Liao, Z., Liu, M., Chen, M., Zhao, L., Lei, H., & Ding, W. (2023). Fractal Analysis on Machined Surface Morphologies of Soft-Brittle KDP Crystals Processed by Micro Ball-End Milling. Materials, 16(5), 1782. https://doi.org/10.3390/ma16051782

Vancouver

Liu Q, Cheng J, Liao Z, Liu M, Chen M, Zhao L, et al. Fractal Analysis on Machined Surface Morphologies of Soft-Brittle KDP Crystals Processed by Micro Ball-End Milling. Materials. 2023;16(5):1782. doi:10.3390/ma16051782

BibTeX
@article{Liu2023,
  author = {Liu, Qi and Cheng, Jian and Liao, Zhirong and Liu, Mingyu and Chen, Mingjun and Zhao, Linjie and Lei, Hongqin and Ding, Wenyu},
  title = {Fractal Analysis on Machined Surface Morphologies of Soft-Brittle KDP Crystals Processed by Micro Ball-End Milling},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {5},
  pages = {1782},
  doi = {10.3390/ma16051782}
}
Kostenlos starten →