EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels

Xiaoyang Jiang, Ke Liu, Mingda Si, Maojun Li iD, Pan Gong iD

Materials · 19.02.2023 · 16 (4) · 1720

DOI: 10.3390/ma16041720 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 19.02.2023. Verfasst von Xiaoyang Jiang und 4 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Advanced Design and Manufacture for Vehicle Body, Hunan University, Changsha 410082, China. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The 17CrNi2MoVNb alloy is widely used for manufacturing heavy-duty gears in vehicles’ transmission systems, where grinding is a significant process affecting gears’ working performance and service life. This work comprehensively analyzed the grinding force, surface morphology, and surface roughness when grinding 17CrNi2MoVNb alloy using alumina and CBN grinding wheels. Results showed that the maximum normal grinding force from the CBN wheel was only ~67% of the one from the alumina wheel. Due to the small size and limited cutting depth of CBN grains, the grinding force increased by about 20% when the grinding depth increased from 0.02 to 0.03 mm for CBN grinding wheels. Surface defects, including cavities and material tearing, were mainly found on the ground surface when using an alumina grinding wheel. The surface roughness Ra recorded from the CBN grinding wheel mainly ranged from 0.263 to 0.410 μm, accounting for less than 40% of the one from the alumina grinding wheel. The information from this work could provide benchmark data and references for optimizing grinding tools and parameters when manufacturing gears in the vehicle industry.

Schlagwörter

Stichwörter der Autor:innen

defectsgrinding forcematerial removal mechanismsurface morphology

Autor:innen und Institutionen

  • State Key Laboratory of Advanced Design and Manufacture for Vehicle Body, Hunan University, Changsha 410082, China.
  • Jianglu Machinery & Electronics Group Co., Ltd., Xiangtan 411100, China.
  • State Key Laboratory of Materials Processing and Die & Mold Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.

ORCID-Profile: Maojun Li, Pan Gong

Zitieren

APA

Jiang, X., Liu, K., Si, M., Li, M., & Gong, P. (2023). Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels. Materials, 16(4), 1720. https://doi.org/10.3390/ma16041720

Vancouver

Jiang X, Liu K, Si M, Li M, Gong P. Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels. Materials. 2023;16(4):1720. doi:10.3390/ma16041720

BibTeX
@article{Jiang2023,
  author = {Jiang, Xiaoyang and Liu, Ke and Si, Mingda and Li, Maojun and Gong, Pan},
  title = {Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {4},
  pages = {1720},
  doi = {10.3390/ma16041720}
}
Kostenlos starten →