EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Process Parameter Selection for Production of Stainless Steel 316L Using Efficient Multi-Objective Bayesian Optimization Algorithm

Timur Chepiga iD, Petr Zhilyaev, Alexander Ryabov iD, Alexey P Simonov iD, Oleg N Dubinin iD, Denis G Firsov iD, Yulia O Kuzminova iD, Stanislav A Evlashin iD

Materials · 25.01.2023 · 16 (3) · 1050

DOI: 10.3390/ma16031050 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 25.01.2023. Verfasst von Timur Chepiga und 7 weiteren Autor:innen. Beteiligte Einrichtung: Skolkovo Institute of Science and Technology, 121205 Moscow, Russia. Die Arbeit wurde bisher 34-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Russian Federation, National Technological Initiative, Foundation for National Technology Initiative’s Projects.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing is a modern technique to produce parts with a complex geometry. However, the choice of the printing parameters is a time-consuming and costly process. In this study, the parameter optimization for the laser powder bed fusion process was investigated. Using state-of-the art multi-objective Bayesian optimization, the set of the most-promising process parameters (laser power, scanning speed, hatch distance, etc.), which would yield parts with the desired hardness and porosity, was established. The Gaussian process surrogate model was built on 57 empirical data points, and through efficient sampling in the design space, we were able to obtain three points in the Pareto front in just over six iterations. The produced parts had a hardness ranging from 224–235 HV and a porosity in the range of 0.2–0.37%. The trained model recommended using the following parameters for high-quality parts: 58 W, 257 mm/s, 45 µm, with a scan rotation angle of 131 degrees. The proposed methodology greatly reduces the number of experiments, thus saving time and resources. The candidate process parameters prescribed by the model were experimentally validated and tested.

Schlagwörter

Stichwörter der Autor:innen

SS316Lmachine learningmetal additive manufacturingmulti-objective optimizationpowder bed fusionprinting parameters

Autor:innen und Institutionen

  • Skolkovo Institute of Science and Technology, 121205 Moscow, Russia.
  • World-Class Research Center, State Marine Technical University, 190121 Saint Petersburg, Russia.

ORCID-Profile: Timur Chepiga, Alexander Ryabov, Alexey P Simonov, Oleg N Dubinin, Denis G Firsov, Yulia O Kuzminova, Stanislav A Evlashin

Förderung

  • Ministry of Science and Higher Education of the Russian Federation
  • National Technological Initiative
  • Foundation for National Technology Initiative’s Projects

Zitieren

APA

Chepiga, T., Zhilyaev, P., Ryabov, A., Simonov, A. P., Dubinin, O. N., Firsov, D. G., Kuzminova, Y. O., & Evlashin, S. A. (2023). Process Parameter Selection for Production of Stainless Steel 316L Using Efficient Multi-Objective Bayesian Optimization Algorithm. Materials, 16(3), 1050. https://doi.org/10.3390/ma16031050

Vancouver

Chepiga T, Zhilyaev P, Ryabov A, Simonov AP, Dubinin ON, Firsov DG, et al. Process Parameter Selection for Production of Stainless Steel 316L Using Efficient Multi-Objective Bayesian Optimization Algorithm. Materials. 2023;16(3):1050. doi:10.3390/ma16031050

BibTeX
@article{Chepiga2023,
  author = {Chepiga, Timur and Zhilyaev, Petr and Ryabov, Alexander and Simonov, Alexey P and Dubinin, Oleg N and Firsov, Denis G and Kuzminova, Yulia O and Evlashin, Stanislav A},
  title = {Process Parameter Selection for Production of Stainless Steel 316L Using Efficient Multi-Objective Bayesian Optimization Algorithm},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {3},
  pages = {1050},
  doi = {10.3390/ma16031050}
}
Kostenlos starten →