EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304

Noha Naeim iD, Mona A AbouEleaz iD, Ahmed Elkaseer iD

Materials · 23.01.2023 · 16 (3) · 1022

DOI: 10.3390/ma16031022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 23.01.2023. Verfasst von Noha Naeim und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Production Engineering and Mechanical Design, Faculty of Engineering, Port Said University, Port Fuad 42526, Egypt. Die Arbeit wurde bisher 37-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Its unexcelled mechanical and physical properties, in addition to its biocompatibility, have made stainless steel 304 a prime candidate for a wide range of applications. Among different manufacturing techniques, electrical discharge machining (EDM) has shown high potential in processing stainless steel 304 in a controllable manner. This paper reports the results of an experimental investigation into the effect of the process parameters on the obtainable surface roughness and material removal rate of stainless steel 304, when slotted using wire EDM. A full factorial design of the experiment was followed when conducting experimental trials in which the effects of the different levels of the five process parameters; applied voltage, traverse feed, pulse-on time, pulse-off time, and current intensity were investigated. The geometry of the cut slots was characterized using the MATLAB image processing toolbox to detect the edge and precise width of the cut slot along its entire length to determine the material removal rate. In addition, the surface roughness of the side walls of the slots were characterized, and the roughness average was evaluated for the range of the process parameters being examined. The effect of the five process parameters on both responses were studied, and the results revealed that the material removal rate is significantly influenced by feed (p-value = 9.72 × 10−29), followed by current tension (p-value = 6.02 × 10−7), and voltage (p-value = 3.77 × 10−5), while the most significant parameters affecting the surface roughness are current tension (p-value = 1.89 × 10−7), followed by pulse-on time (1.602 × 10−5), and pulse-off time (0.0204). The developed regression models and associated prediction plots offer a reliable tool to predict the effect of the process parameters, and thus enable the optimizing of their effects on both responses; surface roughness and material removal rate. The results also reveal the trade-off between the effect of significant process parameters on the material removal rate and surface roughness. This points out the need for a robust multi-objective optimization technique to identify the process window for obtaining high quality surfaces while keeping the material removal rate as high as possible.

Schlagwörter

Stichwörter der Autor:innen

MRRWEDMstainless steel 304statistical analysissurface roughness

Autor:innen und Institutionen

  • Department of Production Engineering and Mechanical Design, Faculty of Engineering, Port Said University, Port Fuad 42526, Egypt.
  • Production Engineering and Mechanical Design Department, Faulty of Engineering, Mansoura University, Mansoura 35516, Egypt.
  • Institute for Automation and Applied Informatics, Karlsruhe Institute of Technology, 76344 Eggenstein-Leopoldshafen, Germany.
  • Department of Mechanical Engineering, Faculty of Engineering, The British University in Egypt (BUE), El-Sherouk City 11837, Egypt.

ORCID-Profile: Noha Naeim, Mona A AbouEleaz, Ahmed Elkaseer

Zitieren

APA

Naeim, N., AbouEleaz, M. A., & Elkaseer, A. (2023). Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304. Materials, 16(3), 1022. https://doi.org/10.3390/ma16031022

Vancouver

Naeim N, AbouEleaz MA, Elkaseer A. Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304. Materials. 2023;16(3):1022. doi:10.3390/ma16031022

BibTeX
@article{Naeim2023,
  author = {Naeim, Noha and AbouEleaz, Mona A and Elkaseer, Ahmed},
  title = {Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {3},
  pages = {1022},
  doi = {10.3390/ma16031022}
}
Kostenlos starten →