EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of a Novel Tape-Casting Multi-Slurry 3D Printing Technology to Fabricate the Ceramic/Metal Part

Cho-Pei Jiang iD, Yulius Shan Romario iD, Ehsan Toyserkani

Materials · 06.01.2023 · 16 (2) · 585

DOI: 10.3390/ma16020585 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.01.2023. Verfasst von Cho-Pei Jiang und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, National Taipei University of Technology, Taipei 10608, Taiwan. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Council, National Science and Technology Council (NSTC) of Taiwan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Printing ceramic/metal parts increases the number of applications in additive manufacturing technology, but printing different materials on the same object with different mechanical properties will increase the difficulty of printing. Multi-material additive manufacturing technology is a solution. This study develops a novel tape-casting 3D printing technology that uses bottom-up photopolymerization to fabricate the green body for low-temperature co-fired ceramics (LTCC) that consist of ceramic and copper. The composition of ceramic and copper slurries is optimized to allow printing without delamination and sintering without cracks. Unlike traditional tape-casting processing, the proposed method deposits two slurries on demand on a transparent film, scrapes it flat, then photopolymerization is induced using a liquid crystal displayer to project the layer pattern beneath the film. The experimental results show that both slurries have good bonding strength, with a weight ratio of powder to resin of 70:30, and print a U-shaped copper volume as a circuit within the LTCC green body. A three-stage sintering parameter is derived using thermogravimetric analysis to ensure good mechanical properties for the sintered part. The SEM images show that the ceramic/copper interface of the LTCC sintered part is well-bonded. The average hardness and flexural strength of the sintered ceramic are 537.1 HV and 126.61 MPa, respectively. Volume shrinkage for the LTCC slurry is 67.97%, which is comparable to the value for a copper slurry of 68.85%. The electrical resistance of the printed copper circuit is 0.175 Ω, which is slightly greater than the theoretical value, hence it has good electrical conductivity. The proposed tape-casting 3D printer is used to print an LTCC benchmark. The sintered benchmark part is validated for the application in the LTCC application.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingmulti-materialtape casting

Autor:innen und Institutionen

  • Department of Mechanical Engineering, National Taipei University of Technology, Taipei 10608, Taiwan.
  • Graduate Institute of Manufacturing Technology, National Taipei University of Technology, Taipei 10608, Taiwan.
  • Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON N2L 3G1, Canada.

ORCID-Profile: Cho-Pei Jiang, Yulius Shan Romario

Förderung

  • National Science and Technology Council
  • National Science and Technology Council (NSTC) of Taiwan

Zitieren

APA

Jiang, C. P., Romario, Y. S., & Toyserkani, E. (2023). Development of a Novel Tape-Casting Multi-Slurry 3D Printing Technology to Fabricate the Ceramic/Metal Part. Materials, 16(2), 585. https://doi.org/10.3390/ma16020585

Vancouver

Jiang CP, Romario YS, Toyserkani E. Development of a Novel Tape-Casting Multi-Slurry 3D Printing Technology to Fabricate the Ceramic/Metal Part. Materials. 2023;16(2):585. doi:10.3390/ma16020585

BibTeX
@article{Jiang2023,
  author = {Jiang, Cho-Pei and Romario, Yulius Shan and Toyserkani, Ehsan},
  title = {Development of a Novel Tape-Casting Multi-Slurry 3D Printing Technology to Fabricate the Ceramic/Metal Part},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {2},
  pages = {585},
  doi = {10.3390/ma16020585}
}
Kostenlos starten →