EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Injection Molding Parameters for Warpage Reduction on Polypropylene Plates

Jorge Jiménez-Armendáriz, Andrea Guevara-Morales, Ulises Figueroa-López, Mariel Alfaro-Ponce, José Martínez-Trinidad, Moises Jimenez-Martinez

Journal of Manufacturing and Materials Processing · 29.11.2025 · 9 (12) · 393

DOI: 10.3390/jmmp9120393 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 29.11.2025. Verfasst von Jorge Jiménez-Armendáriz und 5 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Injection molding is a high-volume manufacturing process widely used for producing polymer components; however, its process parameters strongly influence residual stress, warpage, and the resulting mechanical performance. This work presents a comprehensive factorial design and ANOVA to evaluate the simultaneous effects of the injection temperature, packing pressure, packing time, and specimen orientation on the warpage, hardness, tensile, and flexural properties of polypropylene plates. The results demonstrate that the injection temperature and packing pressure are the dominant factors affecting the hardness and ultimate tensile strength, whereas warpage is mainly governed by the injection temperature and orientation. Under the tested conditions, certain combinations of injection temperature and packing pressure led to an improved mechanical performance; however, these adjustments also produced reductions in other properties, indicating that the balance among parameters depends on the targeted application rather than a single optimal set. Conversely, the parameter combination that produced the lowest warpage still yielded a significant increase in Esec, indicating that reducing the warpage does not necessarily compromise the tensile stiffness. Interestingly, variations in the stress distribution between the tensile and bending tests suggest that the solidification-induced structure of the material influences its mechanical response, with specimens that showed a lower tensile strength exhibiting a comparatively higher resistance under bending. These findings provide new insights into the trade-offs between dimensional accuracy and mechanical performance and offer practical guidelines for optimizing polypropylene injection molding processes.

Zitieren

APA

Jiménez-Armendáriz, J., Guevara-Morales, A., Figueroa-López, U., Alfaro-Ponce, M., Martínez-Trinidad, J., & Jimenez-Martinez, M. (2025). Optimization of Injection Molding Parameters for Warpage Reduction on Polypropylene Plates. Journal of Manufacturing and Materials Processing, 9(12), 393. https://doi.org/10.3390/jmmp9120393

Vancouver

Jiménez-Armendáriz J, Guevara-Morales A, Figueroa-López U, Alfaro-Ponce M, Martínez-Trinidad J, Jimenez-Martinez M. Optimization of Injection Molding Parameters for Warpage Reduction on Polypropylene Plates. Journal of Manufacturing and Materials Processing. 2025;9(12):393. doi:10.3390/jmmp9120393

BibTeX
@article{JimnezArmendriz2025,
  author = {Jiménez-Armendáriz, Jorge and Guevara-Morales, Andrea and Figueroa-López, Ulises and Alfaro-Ponce, Mariel and Martínez-Trinidad, José and Jimenez-Martinez, Moises},
  title = {Optimization of Injection Molding Parameters for Warpage Reduction on Polypropylene Plates},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2025},
  volume = {9},
  number = {12},
  pages = {393},
  doi = {10.3390/jmmp9120393}
}
Kostenlos starten →