EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Recent Progress and Scientific Challenges in Wire-Arc Additive Manufacturing of Metallic Multi-Material Structures

Sainand Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Journal of Manufacturing and Materials Processing · 21.08.2025 · 9 (8) · 284

DOI: 10.3390/jmmp9080284 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 21.08.2025. Verfasst von Sainand Jadhav und 8 weiteren Autor:innen. Die Arbeit wurde bisher 29-mal zitiert (Crossref) und nennt 212 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by a bibliometric analysis of the current research landscape. Conventional and additive manufacturing fabrication approaches are presented. The review highlights key developments in processing strategies and critically evaluates research studies on WAAM of BS and FGMs. Major scientific challenges, including porosity, lack of fusion, residual stresses, cracking, material compatibility, and brittle intermetallic phase formation, are critically analyzed. Additionally, modeling, simulation, and process automation issues are discussed as barriers to industrial-scale implementation. The paper concludes with an outlook on future research directions to address existing challenges and accelerate the adoption of WAAM for complex multi-material components.

Zitieren

APA

Jadhav, S., Kusekar, S., Belure, A., Digole, S., Mali, A., Cheepu, M., Mugale, M., Alkunte, S., & Kim, D. (2025). Recent Progress and Scientific Challenges in Wire-Arc Additive Manufacturing of Metallic Multi-Material Structures. Journal of Manufacturing and Materials Processing, 9(8), 284. https://doi.org/10.3390/jmmp9080284

Vancouver

Jadhav S, Kusekar S, Belure A, Digole S, Mali A, Cheepu M, et al. Recent Progress and Scientific Challenges in Wire-Arc Additive Manufacturing of Metallic Multi-Material Structures. Journal of Manufacturing and Materials Processing. 2025;9(8):284. doi:10.3390/jmmp9080284

BibTeX
@article{Jadhav2025,
  author = {Jadhav, Sainand and Kusekar, Sambhaji and Belure, Akash and Digole, Satyavan and Mali, Abhijeet and Cheepu, Muralimohan and Mugale, Manoj and Alkunte, Suhas and Kim, Duckbong},
  title = {Recent Progress and Scientific Challenges in Wire-Arc Additive Manufacturing of Metallic Multi-Material Structures},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2025},
  volume = {9},
  number = {8},
  pages = {284},
  doi = {10.3390/jmmp9080284}
}
Kostenlos starten →