EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Physical Characteristics and Biocompatibility of 3D-Printed Polylactic-Co-Glycolic Acid Membranes Used for Guided Bone Regeneration

Sidabhat Petposri, Nuttawut Thuaksuban iD, Supanee Buranadham, Trin Suwanrat, Winita Punyodom, Woraporn Supphaprasitt

Journal of Functional Biomaterials · 14.05.2023 · 14 (5) · 275

DOI: 10.3390/jfb14050275 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 14.05.2023. Verfasst von Sidabhat Petposri und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Prince of Songkla University, Hatyai 90112, Songkhla, Thailand. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science, Research and Innovation Fund (NSRF), Prince of Songkla University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bioresorbable polymeric membranes for guided bone regeneration (GBR) were fabricated using the three-dimensional printing technique. Membranes made of polylactic-co-glycolic acid (PLGA), which consist of lactic acid (LA) and glycolic acid in ratios of 10:90 (group A) and 70:30 (group B), were compared. Their physical characteristics including architecture, surface wettability, mechanical properties, and degradability were compared in vitro, and their biocompatibilities were compared in vitro and in vivo. The results demonstrated that the membranes of group B had mechanical strength and could support the proliferation of fibroblasts and osteoblasts significantly better than those of group A (p < 0.05). The degradation rate in Group B was significantly lower than that in Group A, but they significantly produced less acidic environment (p < 0.05). In vivo, the membranes of group B were compared with the commercially available collagen membranes (group C). The amount of newly formed bone of rat’s calvarial defects covered with the membranes of group C was stable after week 2, whereas that of group B increased over time. At week 8, the new bone volumes in group B were greater than those in group C (p > 0.05). In conclusion, the physical and biological properties of the PLGA membrane (LA:GA, 70:30) were suitable for GBR.

Schlagwörter

Stichwörter der Autor:innen

guided bone regenerationmembranepolylactic-co-glycolic acidthree-dimensional printing

Autor:innen und Institutionen

  • Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Prince of Songkla University, Hatyai 90112, Songkhla, Thailand.
  • Department of Prosthetic Dentistry, Faculty of Dentistry, Prince of Songkla University, Hatyai 90112, Songkhla, Thailand.
  • Department of Chemistry, Faculty of Science, Chiang Mai University, Amphur Muang 50200, Chiang Mai, Thailand.

ORCID-Profile: Nuttawut Thuaksuban

Förderung

  • National Science, Research and Innovation Fund (NSRF)
  • Prince of Songkla University

Zitieren

APA

Petposri, S., Thuaksuban, N., Buranadham, S., Suwanrat, T., Punyodom, W., & Supphaprasitt, W. (2023). Physical Characteristics and Biocompatibility of 3D-Printed Polylactic-Co-Glycolic Acid Membranes Used for Guided Bone Regeneration. Journal of Functional Biomaterials, 14(5), 275. https://doi.org/10.3390/jfb14050275

Vancouver

Petposri S, Thuaksuban N, Buranadham S, Suwanrat T, Punyodom W, Supphaprasitt W. Physical Characteristics and Biocompatibility of 3D-Printed Polylactic-Co-Glycolic Acid Membranes Used for Guided Bone Regeneration. Journal of Functional Biomaterials. 2023;14(5):275. doi:10.3390/jfb14050275

BibTeX
@article{Petposri2023,
  author = {Petposri, Sidabhat and Thuaksuban, Nuttawut and Buranadham, Supanee and Suwanrat, Trin and Punyodom, Winita and Supphaprasitt, Woraporn},
  title = {Physical Characteristics and Biocompatibility of 3D-Printed Polylactic-Co-Glycolic Acid Membranes Used for Guided Bone Regeneration},
  journal = {Journal of Functional Biomaterials},
  year = {2023},
  volume = {14},
  number = {5},
  pages = {275},
  doi = {10.3390/jfb14050275}
}
Kostenlos starten →