EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Architecture-Dependent Reinforcement of FFF-Printed PLA Nanocomposites by Functionalized Multi-Walled Carbon Nanotubes

Dorivane Cohen Farias, Diogo Monteiro Porfírio, Miriane Alexandrino Pinheiro, Mário Edson Santos de Sousa, Alessandro José Gomes dos Santos, Douglas Santos Silva, Raí Felipe Pereira Junio, Sergio Neves Monteiro, Marcos Allan Leite dos Reis

Journal of Composites Science · 17.09.2026 · 10 (9) · 494

DOI: 10.3390/jcs10090494 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 17.09.2026. Verfasst von Dorivane Cohen Farias und 8 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Council for Scientific and Technological Development—Brazil.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the combined influence of multi-walled carbon nanotube (MWCNT) concentration and structural architecture on the compressive behavior of fused filament fabrication (FFF)-printed PLA components. Neat PLA and PLA reinforced with 1.0 and 2.0 wt% carboxyl-functionalized MWCNTs were characterized by Raman spectroscopy, DSC, TGA, compression testing, statistical analysis, and scanning electron microscopy. Thermal characterization showed that MWCNT incorporation caused only minor changes in PLA thermal degradation while altering its crystallization behavior. For nearly solid specimens (90% infill), compressive strength increased from 53.4 MPa for neat PLA to 73.6 MPa at 2.0 wt% MWCNTs, although differences among MWCNT concentrations were not statistically significant. Honeycomb structures exhibited the highest mechanical performance at 1.0 wt% MWCNTs, reaching a compressive strength of 33.3 MPa, approximately 59% higher than that of neat PLA, with significant improvements in both compressive strength and elastic modulus. Two-way ANOVA revealed significant interactions between structural architecture and MWCNT concentration for both compressive strength and elastic modulus, demonstrating an architecture-dependent reinforcement response. SEM provided complementary morphological evidence consistent with the observed mechanical trends. These findings demonstrate that the most effective MWCNT concentration depends on structural architecture, highlighting the importance of simultaneously optimizing material composition and geometry in FFF-manufactured polymer nanocomposites.

Förderung

  • National Council for Scientific and Technological Development—Brazil

Zitieren

APA

Farias, D. C., Porfírio, D. M., Pinheiro, M. A., Sousa, M. E. S. D., Santos, A. J. G. D., Silva, D. S., Junio, R. F. P., Monteiro, S. N., & Reis, M. A. L. D. (2026). Architecture-Dependent Reinforcement of FFF-Printed PLA Nanocomposites by Functionalized Multi-Walled Carbon Nanotubes. Journal of Composites Science, 10(9), 494. https://doi.org/10.3390/jcs10090494

Vancouver

Farias DC, Porfírio DM, Pinheiro MA, Sousa MESD, Santos AJGD, Silva DS, et al. Architecture-Dependent Reinforcement of FFF-Printed PLA Nanocomposites by Functionalized Multi-Walled Carbon Nanotubes. Journal of Composites Science. 2026;10(9):494. doi:10.3390/jcs10090494

BibTeX
@article{Farias2026,
  author = {Farias, Dorivane Cohen and Porfírio, Diogo Monteiro and Pinheiro, Miriane Alexandrino and Sousa, Mário Edson Santos de and Santos, Alessandro José Gomes dos and Silva, Douglas Santos and Junio, Raí Felipe Pereira and Monteiro, Sergio Neves and Reis, Marcos Allan Leite dos},
  title = {Architecture-Dependent Reinforcement of FFF-Printed PLA Nanocomposites by Functionalized Multi-Walled Carbon Nanotubes},
  journal = {Journal of Composites Science},
  year = {2026},
  volume = {10},
  number = {9},
  pages = {494},
  doi = {10.3390/jcs10090494}
}
Kostenlos starten →