EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Antisolvent 3D Printing of Gene-Activated Scaffolds for Bone Regeneration

Andrey Vyacheslavovich Vasilyev iD, Irina Alekseevna Nedorubova iD, Viktoria Olegovna Chernomyrdina iD, Anastasiia Yurevna Meglei iD, Viktoriia Pavlovna Basina iD, Anton Vladimirovich Mironov iD, Valeriya Sergeevna Kuznetsova iD, Victoria Alexandrovna Sinelnikova, Olga Anatolievna Mironova, Ekaterina Maksimovna Trifanova iD, Igor Ivanovich Babichenko iD, Vladimir Karpovich Popov iD und 3 weitere

International Journal of Molecular Sciences · 2024

DOI: 10.3390/ijms252413300 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2024. Verfasst von Andrey Vyacheslavovich Vasilyev und 14 weiteren Autor:innen. Beteiligte Einrichtung: Central Research Institute of Dentistry and Maxillofacial Surgery, 119021 Moscow, Russia. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Bone Regeneration, Tissue Scaffolds, Bone Morphogenetic Protein 2. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The use of 3D-printed gene-activated bone grafts represents a highly promising approach in the fields of dentistry and orthopedics. Bioresorbable poly-lactic-co-glycolic acid (PLGA) scaffolds, infused with adenoviral constructs that carry osteoinductive factor genes, may provide an effective alternative to existing bone grafts for the reconstruction of extensive bone defects. This study aims to develop and investigate the properties of 3D scaffolds composed of PLGA and adenoviral constructs carrying the BMP2 gene (Ad-BMP2), both in vitro and in vivo. The elastic modulus of the disk-shaped PLGA scaffolds created using a specialized 3D printer was determined by compressive testing in both axial and radial directions. In vitro cytocompatibility was assessed using adipose-derived stem cells (ADSCs). The ability of Ad-BMP2 to transduce cells was evaluated. The osteoinductive and biocompatible properties of the scaffolds were also assessed in vivo. The Young’s modulus of the 3D-printed PLGA scaffolds exhibited comparable values in both axial and radial compression directions, measuring 3.4 ± 0.7 MPa for axial and 3.17 ± 1.4 MPa for radial compression. The scaffolds promoted cell adhesion and had no cytotoxic effect on ADSCs. Ad-BMP2 successfully transduced the cells and induced osteogenic differentiation in vitro. In vivo studies demonstrated that the 3D-printed PLGA scaffolds had osteoinductive properties, promoting bone formation within the scaffold filaments as well as at the center of a critical calvarial bone defect.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalBone RegenerationTissue ScaffoldsBone Morphogenetic Protein 2OsteogenesisPolylactic Acid-Polyglycolic Acid CopolymerAnimalsCell DifferentiationHumansAdenoviridaeTissue EngineeringStem CellsMiceAdipose TissueCells, CulturedBiocompatible Materials

Stichwörter der Autor:innen

3D printingBMP-2adenoviral vectorbone regeneration

Substanzen

Bone Morphogenetic Protein 2Polylactic Acid-Polyglycolic Acid CopolymerBiocompatible Materials

Autor:innen und Institutionen

  • Central Research Institute of Dentistry and Maxillofacial Surgery, 119021 Moscow, Russia.
  • Research Centre for Medical Genetics, 115478 Moscow, Russia.
  • NRC «Kurchatov Institute», 123182 Moscow, Russia.

ORCID-Profile: Andrey Vyacheslavovich Vasilyev, Irina Alekseevna Nedorubova, Viktoria Olegovna Chernomyrdina, Anastasiia Yurevna Meglei, Viktoriia Pavlovna Basina, Anton Vladimirovich Mironov, Valeriya Sergeevna Kuznetsova, Ekaterina Maksimovna Trifanova, Igor Ivanovich Babichenko, Vladimir Karpovich Popov, Tatiana Borisovna Bukharova

Förderung

  • Russian Science Foundation

Zitieren

APA

Vasilyev, A. V., Nedorubova, I. A., Chernomyrdina, V. O., Meglei, A. Y., Basina, V. P., Mironov, A. V., Kuznetsova, V. S., Sinelnikova, V. A., Mironova, O. A., Trifanova, E. M., Babichenko, I. I., Popov, V. K., Kulakov, A. A., Goldshtein, D. V., & Bukharova, T. B. (2024). Antisolvent 3D Printing of Gene-Activated Scaffolds for Bone Regeneration. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms252413300

Vancouver

Vasilyev AV, Nedorubova IA, Chernomyrdina VO, Meglei AY, Basina VP, Mironov AV, et al. Antisolvent 3D Printing of Gene-Activated Scaffolds for Bone Regeneration. International Journal of Molecular Sciences. 2024. doi:10.3390/ijms252413300

BibTeX
@article{Vasilyev2024,
  author = {Vasilyev, Andrey Vyacheslavovich and Nedorubova, Irina Alekseevna and Chernomyrdina, Viktoria Olegovna and Meglei, Anastasiia Yurevna and Basina, Viktoriia Pavlovna and Mironov, Anton Vladimirovich and Kuznetsova, Valeriya Sergeevna and Sinelnikova, Victoria Alexandrovna and Mironova, Olga Anatolievna and Trifanova, Ekaterina Maksimovna and Babichenko, Igor Ivanovich and Popov, Vladimir Karpovich and Kulakov, Anatoly Alekseevich and Goldshtein, Dmitry Vadimovich and Bukharova, Tatiana Borisovna},
  title = {Antisolvent 3D Printing of Gene-Activated Scaffolds for Bone Regeneration},
  journal = {International Journal of Molecular Sciences},
  year = {2024},
  doi = {10.3390/ijms252413300}
}
Kostenlos starten →