Incorporating Hydrogel (with Low Polymeric Content) into 3D‐Printed PLGA Scaffolds for Local and Sustained Release of BMP2 in Repairing Large Segmental Bone Defects
Advanced Healthcare Materials · 2025
DOI: 10.1002/adhm.202403613 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Healthcare Materials, 2025. Verfasst von Rongpeng Dong und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopedics, The Second Norman Bethune Hospital of Jilin University, Changchun, Jilin, 130014, China. Hauptthemen laut MEDLINE: Bone Morphogenetic Protein 2, Tissue Scaffolds, Hydrogels, Printing, Three-Dimensional. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 67 Literaturangaben. Gefördert von: Jilin Provincial Scientific and Technological Development Program, Natural Science Foundation of Jilin Province, Jilin Provincial Department of Health.
Abstract (Originalsprache)
Treating large bone defects remains a considerable challenge for clinicians: bone repair requires scaffolds with mechanical properties and bioactivities. Herein, based on crosslinking o‐phthalaldehyde (OPA) with amine groups, 4‐arm polyethylene glycol (4armPEG)‐OPA/Gelatin hydrogel loaded with bone morphogenetic protein 2 (BMP2) is prepared and a three dimensional (3D)‐printed poly (lactic‐co‐glycolic acid) (PLGA) porous scaffold is filled with the hydrogel solution. The composite scaffold, with a compression modulus of 0.68 ± 0.097 GPa similar to the cancellous bone, has a porosity of 56.67 ± 4.72% and a pore size of about 380 µm, promoting bone growth. The hydrogel forms a porous network at low concentrations, aiding protein release and cell migration. The hydrogel degrades in approximately three weeks, and the scaffold takes five months, matching bone repair timelines. BMP2 release experiment shows a sustained BMP2 release with a 72.4 ± 0.53% release ratio. The ALP activity test and alizarin red staining shows effective osteogenic promotion, while RT‐PCR confirms BMP2@Gel enhanced COL‐1 and OPN expression. Animal experiments further validate the composite scaffold's bone repair efficacy. This study demonstrates the effectiveness of the hydrogel in releasing BMP2 and the mechanical support of the 3D‐printed PLGA porous scaffold, providing a new treatment for bone defects.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Orthopedics, The Second Norman Bethune Hospital of Jilin University, Changchun, Jilin, 130014, China.
ORCID-Profile: Xueliang Cheng
Förderung
- Jilin Provincial Scientific and Technological Development Program
- Natural Science Foundation of Jilin Province
- Jilin Provincial Department of Health
Zitieren
APA
Dong, R., Kang, M., Qu, Y., Hou, T., Zhao, J., & Cheng, X. (2025). Incorporating Hydrogel (with Low Polymeric Content) into 3D‐Printed PLGA Scaffolds for Local and Sustained Release of BMP2 in Repairing Large Segmental Bone Defects. Advanced Healthcare Materials. https://doi.org/10.1002/adhm.202403613
Vancouver
Dong R, Kang M, Qu Y, Hou T, Zhao J, Cheng X. Incorporating Hydrogel (with Low Polymeric Content) into 3D‐Printed PLGA Scaffolds for Local and Sustained Release of BMP2 in Repairing Large Segmental Bone Defects. Advanced Healthcare Materials. 2025. doi:10.1002/adhm.202403613
BibTeX
@article{Dong2025,
author = {Dong, Rongpeng and Kang, Mingyang and Qu, Yang and Hou, Tingting and Zhao, Jianwu and Cheng, Xueliang},
title = {Incorporating Hydrogel (with Low Polymeric Content) into 3D‐Printed PLGA Scaffolds for Local and Sustained Release of BMP2 in Repairing Large Segmental Bone Defects},
journal = {Advanced Healthcare Materials},
year = {2025},
doi = {10.1002/adhm.202403613}
}
EUVIMED