EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Ceramic and Dentin Thicknesses and Type of Resin-Based Luting Agents on Intrapulpal Temperature Changes during Luting of Ceramic Inlays

Dóra Kincses iD, Dóra Jordáki, Donát Szebeni, Sándor Kunsági-Máté iD, József Szalma iD, Edina Lempel iD

International Journal of Molecular Sciences · 13.03.2023 · 24 (6) · 5466

DOI: 10.3390/ijms24065466 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Molecular Sciences, online erschienen am 13.03.2023. Verfasst von Dóra Kincses und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry and Periodontology, Faculty of Dentistry, University of Pécs Medical School, PTüzér Street 1, 7623 Pécs, Hungary. Hauptthemen laut MEDLINE: Composite Resins, Dental Bonding. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 66 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Hungarian Academy of Sciences, New National Excellence Program of the Ministry for Innovation and Technology from the Source of the National Research, Development and Innovation Fund, University of Pécs Medical School Research Found.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The adhesive cementation of ceramic inlays may increase pulpal temperature (PT) and induce pulpal damage due to heat generated by the curing unit and the exothermic reaction of the luting agent (LA). The aim was to measure the PT rise during ceramic inlay cementation by testing different combinations of dentin and ceramic thicknesses and LAs. The PT changes were detected using a thermocouple sensor positioned in the pulp chamber of a mandibular molar. Gradual occlusal reduction obtained dentin thicknesses of 2.5, 2.0, 1.5, and 1.0 mm. Light-cured (LC) and dual-cured (DC) adhesive cements and preheated restorative resin-based composite (RBC) were applied to luting of 2.0, 2.5, 3.0, and 3.5 mm lithium disilicate ceramic blocks. Differential scanning calorimetry was used to compare the thermal conductivity of dentin and ceramic slices. Although ceramic reduced heat delivered by the curing unit, the exothermic reaction of the LAs significantly increased it in each investigated combination (5.4–7.9 °C). Temperature changes were predominantly influenced by dentin thickness followed by LA and ceramic thickness. Thermal conductivity of dentin was 24% lower than that of ceramic, and its thermal capacity was 86% higher. Regardless of the ceramic thickness, adhesive inlay cementation can significantly increase the PT, especially when the remaining dentin thickness is

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsDental BondingDentinInlaysTemperatureResin CementsCeramicsMaterials Testing

Stichwörter der Autor:innen

adhesive cementceramic thicknessdentin thicknessindirect restorationpreheated resin compositepulpal temperature

Substanzen

Composite ResinsResin Cements

Autor:innen und Institutionen

  • Department of Restorative Dentistry and Periodontology, Faculty of Dentistry, University of Pécs Medical School, PTüzér Street 1, 7623 Pécs, Hungary.
  • Department of Organic and Medicinal Chemistry, Faculty of Pharmacy, University of Pécs, Honvéd Street 1, 7624 Pécs, Hungary.
  • János Szentágothai Research Center, Ifjúság Street 20, 7624 Pécs, Hungary.
  • Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, University of Pécs Medical School, Tüzér Street 1, 7623 Pécs, Hungary.

ORCID-Profile: Dóra Kincses, Sándor Kunsági-Máté, József Szalma, Edina Lempel

Förderung

  • Hungarian Academy of Sciences
  • New National Excellence Program of the Ministry for Innovation and Technology from the Source of the National Research, Development and Innovation Fund
  • University of Pécs Medical School Research Found
  • Nemzeti Kutatási, Fejlesztési és Innovációs Hivatal
  • Tématerületi Kiválóság Program
  • Hungarian Academy of Sciences Bolyai János Research Scholarship
  • ÚNKP-22-5 New National Excellence Program of the Ministry for Innovation and Technology from the Source of the National Research, Development and Innovation Fu…
  • National Research, Development and Innovation Office, Hungary

Zitieren

APA

Kincses, D., Jordáki, D., Szebeni, D., Kunsági-Máté, S., Szalma, J., & Lempel, E. (2023). Effect of Ceramic and Dentin Thicknesses and Type of Resin-Based Luting Agents on Intrapulpal Temperature Changes during Luting of Ceramic Inlays. International Journal of Molecular Sciences, 24(6), 5466. https://doi.org/10.3390/ijms24065466

Vancouver

Kincses D, Jordáki D, Szebeni D, Kunsági-Máté S, Szalma J, Lempel E. Effect of Ceramic and Dentin Thicknesses and Type of Resin-Based Luting Agents on Intrapulpal Temperature Changes during Luting of Ceramic Inlays. International Journal of Molecular Sciences. 2023;24(6):5466. doi:10.3390/ijms24065466

BibTeX
@article{Kincses2023,
  author = {Kincses, Dóra and Jordáki, Dóra and Szebeni, Donát and Kunsági-Máté, Sándor and Szalma, József and Lempel, Edina},
  title = {Effect of Ceramic and Dentin Thicknesses and Type of Resin-Based Luting Agents on Intrapulpal Temperature Changes during Luting of Ceramic Inlays},
  journal = {International Journal of Molecular Sciences},
  year = {2023},
  volume = {24},
  number = {6},
  pages = {5466},
  doi = {10.3390/ijms24065466}
}
Kostenlos starten →