EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on Gel–Resin Composite for Losting Circulation Control to Improve Plugging Effect in Fracture Formation

Jinzhi Zhu, Tao Wang, Shaojun Zhang, Yingrui Bai iD, Guochuan Qin, Jingbin Yang iD

Gels · 07.08.2025 · 11 (8) · 617

DOI: 10.3390/gels11080617 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 07.08.2025. Verfasst von Jinzhi Zhu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Tarim Oilfield Branch, Korla 841000, China. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lost circulation, a prevalent challenge in drilling engineering, poses significant risks including drilling fluid loss, wellbore instability, and environmental contamination. Conventional plugging materials often exhibit an inadequate performance under high-temperature, high-pressure (HTHP), and complex formation conditions. To address that, this study developed a high-performance gel–resin composite plugging material resistant to HTHP environments. By optimizing the formulation of bisphenol-A epoxy resin (20%), hexamethylenetetramine (3%), and hydroxyethyl cellulose (1%), and incorporating fillers such as nano-silica and walnut shell particles, a controllable high-strength plugging system was constructed. Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) confirmed the structural stability of the resin, with an initial decomposition temperature of 220 °C and a compressive strength retention of 14.4 MPa after 45 days of aging at 140 °C. Rheological tests revealed shear-thinning behavior (initial viscosity: 300–350 mPa·s), with viscosity increasing marginally to 51 mPa·s after 10 h of stirring at ambient temperature, demonstrating superior pumpability. Experimental results indicated excellent adaptability of the system to drilling fluid contamination (compressive strength: 5.04 MPa at 20% dosage), high salinity (formation water salinity: 166.5 g/L), and elevated temperatures (140 °C). In pressure-bearing plugging tests, the resin achieved a breakthrough pressure of 15.19 MPa in wedge-shaped fractures (inlet: 7 mm/outlet: 5 mm) and a sand-packed tube sealing pressure of 11.25 MPa. Acid solubility tests further demonstrated outstanding degradability, with a 97.69% degradation rate after 24 h in 15% hydrochloric acid at 140 °C. This study provides an efficient, stable, and environmentally friendly solution for mitigating drilling fluid loss in complex formations, exhibiting significant potential for engineering applications.

Schlagwörter

Stichwörter der Autor:innen

acid solubilitydrilling fluid lossgel–resinhigh-temperature- and high-pressure-resistant systemplugging systemthermal stability

Autor:innen und Institutionen

  • Tarim Oilfield Branch, Korla 841000, China.
  • R&D Center for Ultra Deep Complex Reservior Exploration and Development, China National Petroleum Corporation, Korla 841000, China.
  • Xinjiang Key Laboratory of Ultra-Deep Oil and Gas, Korla 841000, China.
  • Engineering Research Center for Ultra-Deep Complex Reservoir Exploration and Development, Korla 841000, China.
  • State Key Laboratory of Deep Oil and Gas, China University of Petroleum (East China), Qingdao 266580, China.

ORCID-Profile: Yingrui Bai, Jingbin Yang

Zitieren

APA

Zhu, J., Wang, T., Zhang, S., Bai, Y., Qin, G., & Yang, J. (2025). Study on Gel–Resin Composite for Losting Circulation Control to Improve Plugging Effect in Fracture Formation. Gels, 11(8), 617. https://doi.org/10.3390/gels11080617

Vancouver

Zhu J, Wang T, Zhang S, Bai Y, Qin G, Yang J. Study on Gel–Resin Composite for Losting Circulation Control to Improve Plugging Effect in Fracture Formation. Gels. 2025;11(8):617. doi:10.3390/gels11080617

BibTeX
@article{Zhu2025,
  author = {Zhu, Jinzhi and Wang, Tao and Zhang, Shaojun and Bai, Yingrui and Qin, Guochuan and Yang, Jingbin},
  title = {Study on Gel–Resin Composite for Losting Circulation Control to Improve Plugging Effect in Fracture Formation},
  journal = {Gels},
  year = {2025},
  volume = {11},
  number = {8},
  pages = {617},
  doi = {10.3390/gels11080617}
}
Kostenlos starten →