EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Reproducible Screening Procedure for Hardfaced Sealing Surfaces of Wedge Gate Valves: An Sv-10Kh17T (ER430Ti) Case Study

Zhanara Mussina, Dinara Iskakova, Assylbek Kassenov, Aizhan Taskarina, Tatyana Lub, Leila Mussina, Zaure Ibragimova, Almagul Baltabekova, Davran Radjibaev

Eng · 06.11.2026 · 7 (11) · 620

DOI: 10.3390/eng7110620 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Eng, online erschienen am 06.11.2026. Verfasst von Zhanara Mussina und 8 weiteren Autor:innen. Die Arbeit nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Gate-valve repair decisions may rely on numerical and tribological datasets generated at different scales. Combining them can produce unsupported claims when wear results are reported only as ranges. This study introduces a reproducible screening procedure and demonstrates it with previously published results for Grade 20 steel with and without Sv-10Kh17T (ER430Ti) hardfacing. For each lower-is-better wear metric, an interval improvement factor was calculated from untreated and hardfaced ranges; strict dominance required the conservative lower bound to exceed unity. The tribological screen was combined with component-level stress and displacement ratios and an evidence-sufficiency grade. For dry contact, the improvement-factor intervals were 1.67–4.00 for mass loss and 1.60–4.00 for wear depth. In distilled water, the corresponding intervals were 1.50–5.00 and 1.25–4.00. For HOCUT 795 H-eu, both lower bounds equaled 1.00; thus, the range-only data did not establish strict dominance. The component-scale stress ratio after hardfacing was 0.895 for the water load case, 1.039 for steam, and 1.114 for petroleum products. The procedure classifies the hardfacing as eligible for validation under dry and aqueous laboratory conditions, but not as qualified for deployment because allowable-stress verification, mesh convergence, interface validation, and replicate-level wear statistics are unavailable. The rule separates reduced material removal from structural admissibility and service-life claims.

Förderung

  • Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Mussina, Z., Iskakova, D., Kassenov, A., Taskarina, A., Lub, T., Mussina, L., Ibragimova, Z., Baltabekova, A., & Radjibaev, D. (2026). A Reproducible Screening Procedure for Hardfaced Sealing Surfaces of Wedge Gate Valves: An Sv-10Kh17T (ER430Ti) Case Study. Eng, 7(11), 620. https://doi.org/10.3390/eng7110620

Vancouver

Mussina Z, Iskakova D, Kassenov A, Taskarina A, Lub T, Mussina L, et al. A Reproducible Screening Procedure for Hardfaced Sealing Surfaces of Wedge Gate Valves: An Sv-10Kh17T (ER430Ti) Case Study. Eng. 2026;7(11):620. doi:10.3390/eng7110620

BibTeX
@article{Mussina2026,
  author = {Mussina, Zhanara and Iskakova, Dinara and Kassenov, Assylbek and Taskarina, Aizhan and Lub, Tatyana and Mussina, Leila and Ibragimova, Zaure and Baltabekova, Almagul and Radjibaev, Davran},
  title = {A Reproducible Screening Procedure for Hardfaced Sealing Surfaces of Wedge Gate Valves: An Sv-10Kh17T (ER430Ti) Case Study},
  journal = {Eng},
  year = {2026},
  volume = {7},
  number = {11},
  pages = {620},
  doi = {10.3390/eng7110620}
}
Kostenlos starten →