EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modification of the Tribomechanical Cutting Regime in Longitudinal-Torsional Ultrasonic Milling: From Adhesion to Controlled Fragmentation

Oussama Beldi, Tarik Zarrouk, Ahmed Abbadi, Mohammed Nouari, Wenfeng Ding, Mohammed Abbadi, Jamal-Eddine Salhi, Mohammed Barboucha

Eng · 13.04.2026 · 7 (4) · 177

DOI: 10.3390/eng7040177 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Eng, online erschienen am 13.04.2026. Verfasst von Oussama Beldi und 7 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Machining Nomex honeycomb structures presents a major challenge due to their thin-walled architecture, orthotropic behavior, and sensitivity to adhesion and delamination. This study develops a three-dimensional numerical model using Abaqus/Explicit to analyze ultrasonic vibration-assisted milling in longitudinal and longitudinal-torsional modes. The model incorporates orthotropic behavior with progressive damage based on Tsai-Wu and experimental friction calibration to accurately reproduce tribological conditions. A parametric analysis examines the effect of vibration mode, amplitude (5–25 µm), frequency (21–22.5 kHz), cutting width, and tool geometry on stresses, bond wear, and material buildup. An optimal coefficient of friction ensures excellent simulation–experiment agreement. Compared to conventional milling, the longitudinal-torsional configuration reduces cutting forces by up to 50%, while frequency optimization allows for gains of 40 to 60%. Hybrid vibration coupling establishes intermittent contact and oscillatory micro-shearing, limiting adhesion and build-up. Thus, longitudinal-torsional assistance improves tribological stability, tool life and wall integrity, offering a validated digital strategy to optimize ultrasonic milling of composite honeycomb structures.

Zitieren

APA

Beldi, O., Zarrouk, T., Abbadi, A., Nouari, M., Ding, W., Abbadi, M., Salhi, J., & Barboucha, M. (2026). Modification of the Tribomechanical Cutting Regime in Longitudinal-Torsional Ultrasonic Milling: From Adhesion to Controlled Fragmentation. Eng, 7(4), 177. https://doi.org/10.3390/eng7040177

Vancouver

Beldi O, Zarrouk T, Abbadi A, Nouari M, Ding W, Abbadi M, et al. Modification of the Tribomechanical Cutting Regime in Longitudinal-Torsional Ultrasonic Milling: From Adhesion to Controlled Fragmentation. Eng. 2026;7(4):177. doi:10.3390/eng7040177

BibTeX
@article{Beldi2026,
  author = {Beldi, Oussama and Zarrouk, Tarik and Abbadi, Ahmed and Nouari, Mohammed and Ding, Wenfeng and Abbadi, Mohammed and Salhi, Jamal-Eddine and Barboucha, Mohammed},
  title = {Modification of the Tribomechanical Cutting Regime in Longitudinal-Torsional Ultrasonic Milling: From Adhesion to Controlled Fragmentation},
  journal = {Eng},
  year = {2026},
  volume = {7},
  number = {4},
  pages = {177},
  doi = {10.3390/eng7040177}
}
Kostenlos starten →