EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cyclic Fatigue Resistance and Phase Transformation Behavior of SlimShaper and SlimShaper PRO NiTi Instruments: A Mechanical and Thermal Analysis

Cristina Scolaro iD, Francesco Puleio iD, Andrea Sili iD, Annamaria Visco iD

Dentistry Journal · 04.01.2026 · 14 (1) · 22

DOI: 10.3390/dj14010022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 04.01.2026. Verfasst von Cristina Scolaro und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering, University of Messina, 98166 Messina, Italy. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

This study compared the cyclic fatigue resistance and the mechanical, thermal, and metallurgical characteristics of SlimShaper® and SlimShaper PRO® instruments. Both sequences include three instruments (ZS1–ZS3) with identical geometries, although SlimShaper PRO features an apically modified thermal treatment.

Methods

Cyclic fatigue tests were performed using a standardized metallic guide with a 45° curvature, on six instruments of each sequence type. Fractured segments were measured, and fracture surfaces were analyzed using optical microscopy and Scanning Electron Microscopy (SEM). Elemental composition was assessed by Energy-dispersive Spectroscopy (EDS), while Differential Scanning Calorimetry (DSC) was used to determine transformation temperatures and enthalpy.

Results

ZS1 and ZS1 PRO exhibited comparable cyclic fatigue resistance, whereas ZS2 and ZS3 showed significantly higher resistance than their PRO counterparts. SlimShaper PRO® instruments fractured with segments approximately 0.5–1 mm longer. EDS confirmed that both instruments were made of NiTi, with minor differences in surface composition, while DSC demonstrated similar enthalpy values but distinct transformation ranges. At room temperature (27 °C), SlimShaper® ZS2 remained predominantly martensitic, whereas ZS2 PRO could be partially austenitic, explaining its observed reduced fatigue resistance. The results of the DSC allowed to deduce the microstructure and thus the fatigue behavior at the temperature of the oral cavity.

Conclusions

SlimShaper ZS2 and ZS3 showed significantly greater cyclic fatigue resistance than their PRO counterparts, while DSC analysis revealed distinct differences in phase transformation behavior that explain their mechanical performance.

Schlagwörter

Stichwörter der Autor:innen

austenitecyclic fatigue resistanceendodontic rotary instrumentsmartensitephase transformationthermal treatment

Autor:innen und Institutionen

  • Department of Engineering, University of Messina, 98166 Messina, Italy.
  • Department of Biomedical and Dental Sciences and Morphofunctional Imaging, University of Messina, 98122 Messina, Italy.
  • Institute for Polymers, Composites and Biomaterials-CNR IPCB, Via Paolo Gaifami 18, 95126 Catania, Italy.

ORCID-Profile: Cristina Scolaro, Francesco Puleio, Andrea Sili, Annamaria Visco

Zitieren

APA

Scolaro, C., Puleio, F., Sili, A., & Visco, A. (2026). Cyclic Fatigue Resistance and Phase Transformation Behavior of SlimShaper and SlimShaper PRO NiTi Instruments: A Mechanical and Thermal Analysis. Dentistry Journal, 14(1), 22. https://doi.org/10.3390/dj14010022

Vancouver

Scolaro C, Puleio F, Sili A, Visco A. Cyclic Fatigue Resistance and Phase Transformation Behavior of SlimShaper and SlimShaper PRO NiTi Instruments: A Mechanical and Thermal Analysis. Dentistry Journal. 2026;14(1):22. doi:10.3390/dj14010022

BibTeX
@article{Scolaro2026,
  author = {Scolaro, Cristina and Puleio, Francesco and Sili, Andrea and Visco, Annamaria},
  title = {Cyclic Fatigue Resistance and Phase Transformation Behavior of SlimShaper and SlimShaper PRO NiTi Instruments: A Mechanical and Thermal Analysis},
  journal = {Dentistry Journal},
  year = {2026},
  volume = {14},
  number = {1},
  pages = {22},
  doi = {10.3390/dj14010022}
}
Kostenlos starten →