EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface Roughness and Microbial Adhesion on Four Provisional Prosthodontic Restorative Materials

Ola Al Hatem, Joe C Ontiveros iD, Donald M Belles, Maria D Gonzalez iD, Ransome van der Hoeven iD

Dentistry Journal · 27.10.2025 · 13 (11) · 498

DOI: 10.3390/dj13110498 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 27.10.2025. Verfasst von Ola Al Hatem und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry and Prosthodontics, School of Dentistry, The University of Texas Health Science Center, Houston, TX 77054, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The University of Texas Health Science Center at Houston, School of Dentistry, The University of Iowa, College of Dentistry and Dental Clinics, University of Texas, Health Science Center, School of Dentistry at Houston.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

The aim of this study was to evaluate surface roughness (Ra) and microbial adhesion on four provisional prosthodontic materials in comparison to zirconium oxide.

Methods

Four provisional prosthodontic restorative materials were evaluated in this study: poly methyl methacrylate (PMMA) acrylic resin (ALIKE; GC America Inc., Alsip, IL, USA), dimethacrylate (Bis-acryl) resin (Integrity; Dentsply Sirona, Charlotte, NC, USA), 3D-printed temporary crown and bridge resin (Formlabs Inc., Somerville, MA, USA), prepolymerized poly methyl methacrylate (milled PMMA) (Harvest Dental Laboratory Products, Brea, CA, USA), and zirconium oxide (Ivoclar Vivadent AG, Liechtenstein, Germany). A total of 90 samples were prepared and divided into two groups per material (treated and untreated). Provisional material samples were prepared per manufacturer’s instructions, polished with the same sequence using acrylic burs followed by Acrylipro silicone polishers (Brasseler, Savannah, GA, USA), and pumice with a goat brush. Zirconia was polished with a green grinding stone (ZR Grinders; Brassseler, Savannah, GA, USA), followed by a feather lite (Dialite ZR polisher; Brasseler, Savannah, GA, USA). The Ra of all samples was measured using a digital profilometer. Sterilized samples were incubated in Todd Hewitt yeast extract (THY) broth containing Candida albicans SC5314 and Streptococcus mutans BM71 at 37 °C under anaerobic conditions for 72 h. Subsequently, the number of colony-forming units (CFU) adhered to each sample was determined by serial dilution plating. Normality and homoscedasticity were assessed prior to statistical analysis. Welch’s ANOVA was then performed to evaluate differences among all samples, followed by Games–Howell post hoc tests for pairwise comparisons. A p < 0.05 was considered significant in all experiments.

Results

Zirconia demonstrated the lowest surface roughness and significantly reduced adhesion of S. mutans and C. albicans compared to all other materials (p < 0.001). Milled PMMA exhibited significantly lower roughness and microbial adhesion than conventional PMMA (p < 0.001), with no significant difference from Printed PMMA in microbial adhesion. Additional pairwise differences were observed between Bis-acryl and PMMA (p = 0.0425), Milled and Printed PMMA (p < 0.0001), and Bis-acryl and Printed PMMA (p < 0.0001).

Conclusions

Zirconia and milled PMMA showed superior surface properties and reduced microbial adhesion, supporting their use in long-term provisional restorations. Materials with higher microbial retention, such as self-curing PMMA, bis-acryl, and 3D-printed resins, may be less suitable for extended use. These findings guide material selection to improve clinical outcomes and highlight the need for further in vivo research.

Schlagwörter

Stichwörter der Autor:innen

dimethacrylatepoly (methyl methacrylate)zirconium oxide

Autor:innen und Institutionen

  • Department of Restorative Dentistry and Prosthodontics, School of Dentistry, The University of Texas Health Science Center, Houston, TX 77054, USA.
  • Department of Diagnostic and Biomedical Sciences, School of Dentistry, The University of Texas Health Science Center, Houston, TX 77054, USA.
  • Iowa Institute for Oral Health Research, College of Dentistry, University of Iowa, Iowa City, IA 52242, USA.
  • Department of Periodontics, College of Dentistry, University of Iowa, Iowa City, IA 52242, USA.

ORCID-Profile: Joe C Ontiveros, Maria D Gonzalez, Ransome van der Hoeven

Förderung

  • The University of Texas Health Science Center at Houston, School of Dentistry
  • The University of Iowa, College of Dentistry and Dental Clinics
  • University of Texas, Health Science Center, School of Dentistry at Houston
  • University of Iowa, College of Dentistry and Dental Clinics

Zitieren

APA

Al Hatem, O., Ontiveros, J. C., Belles, D. M., Gonzalez, M. D., & van der Hoeven, R. (2025). Surface Roughness and Microbial Adhesion on Four Provisional Prosthodontic Restorative Materials. Dentistry Journal, 13(11), 498. https://doi.org/10.3390/dj13110498

Vancouver

Al Hatem O, Ontiveros JC, Belles DM, Gonzalez MD, van der Hoeven R. Surface Roughness and Microbial Adhesion on Four Provisional Prosthodontic Restorative Materials. Dentistry Journal. 2025;13(11):498. doi:10.3390/dj13110498

BibTeX
@article{AlHatem2025,
  author = {Al Hatem, Ola and Ontiveros, Joe C and Belles, Donald M and Gonzalez, Maria D and van der Hoeven, Ransome},
  title = {Surface Roughness and Microbial Adhesion on Four Provisional Prosthodontic Restorative Materials},
  journal = {Dentistry Journal},
  year = {2025},
  volume = {13},
  number = {11},
  pages = {498},
  doi = {10.3390/dj13110498}
}
Kostenlos starten →