Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis
Dentistry Journal · 31.10.2023 · 11 (11) · 254
DOI: 10.3390/dj11110254 ↗Kurz gefasst
Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 31.10.2023. Verfasst von Pablo Machado Soares und 8 weiteren Autor:innen. Beteiligte Einrichtung: Post-Graduate Program in Oral Sciences, Center for Development of Advanced Materials, Division of Prosthodontics-Biomaterials, Federal University of …. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Brazilian Federal Agency for Coordination of Improvement of Higher Education Personnel—CAPES, P.M.S. and L.S.R. Doctorate’s scholarships, L.S.R. doctorate sandwich scholarship.
Abstract (Originalsprache)
This study evaluated the mechanical behavior and risk of failure of three CAD-CAM crowns repaired with different resin composites through a three-dimensional (3D) finite element analysis. Three-dimensional models of different cusp-repaired (conventional nanohybrid, bulk-fill, and flowable resin composites) crowns made of zirconia, lithium disilicate, and CAD-CAM resin composite were designed, fixed at the cervical level, and loaded in 100 N at the working cusps, including the repaired one. The models were analyzed to determine the Maximum Principal and Maximum Shear stresses (MPa). Complementary, an in vitro shear bond strength test (n = 10) was performed to calculate the risk of failure for each experimental group. The stress distribution among the models was similar when considering the same restorative material. The crown material affected the stress concentration, which was higher for the ceramic models (±9 MPa for shear stress; ±3 MPa for tensile stress) than for the CAD-CAM composite (±7 MPa for shear stress; ±2 MPa for tensile stress). The shear bond strength was higher for the repaired CAD-CAM resin composite (±17 MPa) when compared to the ceramics (below 12 MPa for all groups), while the repair materials showed similar behavior for each substrate. The stress distribution is more homogenous for repaired resin composite crowns, and a flowable direct resin composite seems suitable to repair ceramic crowns with less risk of failure.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Post-Graduate Program in Oral Sciences, Center for Development of Advanced Materials, Division of Prosthodontics-Biomaterials, Federal University of Santa Maria (UFSM), Santa Maria 97105-900, Brazil.
- Department of Dental Materials Science, Academic Centre for Dentistry Amsterdam (ACTA), Universiteit van Amsterdam and Vrije Universiteit Amsterdam, 1081 LA Amsterdam, The Netherlands.
- Department of Reconstructive Oral Care, Academic Centre for Dentistry Amsterdam (ACTA), Universiteit van Amsterdam and Vrije Universiteit Amsterdam, 1081 LA Amsterdam, The Netherlands.
ORCID-Profile: Amanda Maria de Oliveira Dal Piva, João Paulo Mendes Tribst
Förderung
- the Brazilian Federal Agency for Coordination of Improvement of Higher Education Personnel—CAPES
- P.M.S. and L.S.R. Doctorate’s scholarships
- L.S.R. doctorate sandwich scholarship
Zitieren
APA
Soares, P. M., da Rosa, L. S., Pereira, G. K. R., Valandro, L. F., Rippe, M. P., Dal Piva, A. M. O., Feilzer, A. J., Kleverlaan, C. J., & Tribst, J. P. M. (2023). Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis. Dentistry Journal, 11(11), 254. https://doi.org/10.3390/dj11110254
Vancouver
Soares PM, da Rosa LS, Pereira GKR, Valandro LF, Rippe MP, Dal Piva AMO, et al. Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis. Dentistry Journal. 2023;11(11):254. doi:10.3390/dj11110254
BibTeX
@article{Soares2023,
author = {Soares, Pablo Machado and da Rosa, Lucas Saldanha and Pereira, Gabriel Kalil Rocha and Valandro, Luiz Felipe and Rippe, Marilia Pivetta and Dal Piva, Amanda Maria de Oliveira and Feilzer, Albert J and Kleverlaan, Cornelis J and Tribst, João Paulo Mendes},
title = {Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis},
journal = {Dentistry Journal},
year = {2023},
volume = {11},
number = {11},
pages = {254},
doi = {10.3390/dj11110254}
}
EUVIMED