EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Electrolytic-Plasma Nitriding of Austenitic Stainless Steels After Mechanical Surface Treatment

Bauyrzhan Rakhadilov, Zarina Satbayeva, Almasbek Maulit, Nurlat Kadyrbolat, Anuar Rustemov

Crystals · 17.11.2025 · 15 (11) · 992

DOI: 10.3390/cryst15110992 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 17.11.2025. Verfasst von Bauyrzhan Rakhadilov und 4 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Committee of Science of the Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, the effect of preliminary mechanical surface treatment on the kinetics of formation, phase composition, and functional properties of the nitrided layer during electrolytic-plasma nitriding (EPN) of austenitic stainless steel 12Kh18N10T (AISI 321) was investigated. In contrast to traditional approaches, for the first time, this work establishes a direct correlation between the degree of surface deformation induced by shot peening and the formation of the expanded austenite (γN) phase under low-temperature plasma conditions. Quantitative X-ray phase analysis revealed a lattice parameter expansion of Δa/a0 ≈ 1.4–1.8% and a gradual transformation of γ-Fe → γN without the formation of CrN nitrides at moderate intensity of preliminary treatment. According to SEM/EDS data and microhardness profiles, a multilayer structure was formed, consisting of a thin surface film of CrN/Fe4N, a developed γN zone with a thickness of 12–15 µm, and a stable austenitic γ-Fe matrix. The surface microhardness increases to 880 ± 20 HV, while the friction coefficient decreases to 0.35–0.40, corresponding to a wear reduction of approximately 55% compared to the initial steel. The results provide a mechanistic understanding of nitrogen diffusion through defect-enriched subsurface layers and show that optimal preliminary deformation (d = 6 mm, v = 40 Hz, t = 20 min) promotes controlled formation of the γN phase with minimal lattice instability. The proposed combined approach—shot peening + EPN—is an effective method for producing wear- and corrosion-resistant surfaces of austenitic steels under atmospheric plasma conditions.

Förderung

  • Committee of Science of the Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Rakhadilov, B., Satbayeva, Z., Maulit, A., Kadyrbolat, N., & Rustemov, A. (2025). Electrolytic-Plasma Nitriding of Austenitic Stainless Steels After Mechanical Surface Treatment. Crystals, 15(11), 992. https://doi.org/10.3390/cryst15110992

Vancouver

Rakhadilov B, Satbayeva Z, Maulit A, Kadyrbolat N, Rustemov A. Electrolytic-Plasma Nitriding of Austenitic Stainless Steels After Mechanical Surface Treatment. Crystals. 2025;15(11):992. doi:10.3390/cryst15110992

BibTeX
@article{Rakhadilov2025,
  author = {Rakhadilov, Bauyrzhan and Satbayeva, Zarina and Maulit, Almasbek and Kadyrbolat, Nurlat and Rustemov, Anuar},
  title = {Electrolytic-Plasma Nitriding of Austenitic Stainless Steels After Mechanical Surface Treatment},
  journal = {Crystals},
  year = {2025},
  volume = {15},
  number = {11},
  pages = {992},
  doi = {10.3390/cryst15110992}
}
Kostenlos starten →