EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Small Deformations on Optimisation of Final Crystallographic Texture and Microstructure in Non-Oriented FeSi Steels

Ivan Petrišinec, Marcela Motýľová, František Kováč, Ladislav Falat, Viktor Puchý, Mária Podobová, František Kromka

Crystals · 26.09.2025 · 15 (10) · 839

DOI: 10.3390/cryst15100839 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 26.09.2025. Verfasst von Ivan Petrišinec und 6 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Funded by the EU NextGenerationEU through the Recovery and Resilience Plan for Slovakia.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Improving the isotropic magnetic properties of FeSi electrical steels has traditionally focused on enhancing their crystallographic texture and microstructural morphology. Strengthening the cube texture within a ferritic matrix of optimal grain size is known to reduce core losses and increase magnetic induction. However, conventional cold rolling followed by annealing remains insufficient to optimise the magnetic performance of thin FeSi strips fully. This study explores an alternative approach based on grain boundary migration driven by temperature gradients combined with deformation gradients, either across the sheet thickness or between neighbouring grains, in thin, weakly deformed non-oriented (NO) electrical steel sheets. The concept relies on deformation-induced grain growth supported by rapid heat transport to promote the preferential formation of coarse grains with favourable orientations. Experimental material consisted of vacuum-degassed FeSi steel with low silicon content. Controlled deformation was introduced by temper rolling at room temperature with 2–40% thickness reductions, followed by rapid recrystallisation annealing at 950 °C. Microstructure, texture, and residual strain distributions were analysed using inverse pole figure (IPF) maps, kernel average misorientation (KAM) maps, and orientation distribution function (ODF) sections derived from electron backscattered diffraction (EBSD) data. This combined thermomechanical treatment produced coarse-grained microstructures with an enhanced cube texture component, reducing coercivity from 162 A/m to 65 A/m. These results demonstrate that temper rolling combined with dynamic annealing can surpass the limitations of conventional processing routes for NO FeSi steels.

Förderung

  • Funded by the EU NextGenerationEU through the Recovery and Resilience Plan for Slovakia

Zitieren

APA

Petrišinec, I., Motýľová, M., Kováč, F., Falat, L., Puchý, V., Podobová, M., & Kromka, F. (2025). Effect of Small Deformations on Optimisation of Final Crystallographic Texture and Microstructure in Non-Oriented FeSi Steels. Crystals, 15(10), 839. https://doi.org/10.3390/cryst15100839

Vancouver

Petrišinec I, Motýľová M, Kováč F, Falat L, Puchý V, Podobová M, et al. Effect of Small Deformations on Optimisation of Final Crystallographic Texture and Microstructure in Non-Oriented FeSi Steels. Crystals. 2025;15(10):839. doi:10.3390/cryst15100839

BibTeX
@article{Petriinec2025,
  author = {Petrišinec, Ivan and Motýľová, Marcela and Kováč, František and Falat, Ladislav and Puchý, Viktor and Podobová, Mária and Kromka, František},
  title = {Effect of Small Deformations on Optimisation of Final Crystallographic Texture and Microstructure in Non-Oriented FeSi Steels},
  journal = {Crystals},
  year = {2025},
  volume = {15},
  number = {10},
  pages = {839},
  doi = {10.3390/cryst15100839}
}
Kostenlos starten →