EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder

Mustafa Tobah, Mohsen T. Andani, Bibhu P. Sahu, Amit Misra

Crystals · 15.01.2024 · 14 (1) · 81

DOI: 10.3390/cryst14010081 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 15.01.2024. Verfasst von Mustafa Tobah und 3 weiteren Autor:innen. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Center for Research Excellence on Dynamically Deformed Solids.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The powder bed fusion–laser beam (PBF-LB) process, a method of additive manufacturing (AM), was used to print duplex stainless steel (DSS) using commercial-grade 2507 powders. While conventionally processed DSS has a two-phase microstructure consisting of 50% austenite and 50% ferrite, the PBF-LB-printed 2507 alloy was nearly 100% ferrite. Optimal processing conditions that minimized porosity were determined to be 290 W laser power and 1000 mm/s scan speed, and grain size, texture, and phases were characterized as a function of laser power and scan speed. Grain size increased with increasing laser power but decreased with increasing scan speed. A texture diminished with increasing scan speed from 1000 mm/s to 1400 mm/s. No austenite phase was detected. Transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) characterization revealed nanoscale chromium nitride precipitates in the ferritic matrix (incoherent hexagonal close-packed (HCP) precipitates at grain boundaries and coherent body-centered cubic (BCC) precipitates within the grains) and a high density of tangled dislocations. Tensile tests of as-printed alloys showed a yield strength of 570 MPa, an ultimate tensile strength of 756 MPa, and an elongation to failure of 10%. The tensile properties were analyzed based on the observed microstructure considering grain size, nanoscale precipitates, and the high density of dislocations.

Förderung

  • Center for Research Excellence on Dynamically Deformed Solids

Zitieren

APA

Tobah, M., Andani, M. T., Sahu, B. P., & Misra, A. (2024). Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder. Crystals, 14(1), 81. https://doi.org/10.3390/cryst14010081

Vancouver

Tobah M, Andani MT, Sahu BP, Misra A. Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder. Crystals. 2024;14(1):81. doi:10.3390/cryst14010081

BibTeX
@article{Tobah2024,
  author = {Tobah, Mustafa and Andani, Mohsen T. and Sahu, Bibhu P. and Misra, Amit},
  title = {Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder},
  journal = {Crystals},
  year = {2024},
  volume = {14},
  number = {1},
  pages = {81},
  doi = {10.3390/cryst14010081}
}
Kostenlos starten →