Study on the Wear Resistance of Laser Cladding h-BN Reinforced by TiCN/Ni-Based Coating on TC4 Alloy Surface
Coatings · 18.04.2026 · 16 (4) · 490
DOI: 10.3390/coatings16040490 ↗Kurz gefasst
Fachartikel in der Zeitschrift Coatings, online erschienen am 18.04.2026. Verfasst von Yu Liu und 5 weiteren Autor:innen. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Jiujiang Key Research and Development Program, 2024 Key Research Platforms and Projects for Universities in Guangdong Province, 2024 University Research Project of Guangzhou Education Bureau.
Abstract (Originalsprache)
Three Ni-based composite coatings with varying TiCN/h-BN contents were fabricated on the surface of Ti-6Al-4V (TC4) alloy by laser cladding. The coatings were formulated with a fixed 15% TiCN and 0%, 2% and 5% h-BN, corresponding to L1–L3 coatings. The microstructure and phase composition were fully characterized and investigated. In addition, the microhardness and wear resistance of the coating were evaluated too. The analysis revealed that the L1–L3 coatings primarily consisted of Ti, TiNi, Ti(C, N) and TiAl3 phases. Microstructural analysis indicated that the top region of the coating was predominantly composed of granular crystals, while the middle and bonding regions featured a combination of dendrites and white granular crystals. The average microhardness values for the L1–L3 coatings were measured at 1203.8, 1216.8 and 1235.5 HV0.2, respectively, while the corresponding wear volumes were 0.098, 0.094 and 0.086 mm3. As the h-BN content increased, the microstructure of the Ni-based composite coating became finer and finer. Some TiB particles were also generated in the coating, which made the average microhardness and wear resistance increase gradually. Notably, the coating with 5% h-BN demonstrated the highest average microhardness and optimal wear resistance. Compared with the substrate, 5% h-BN increased the wear resistance of the substrate by 47.6%. The primary wear mechanism observed was abrasive wear.
Förderung
- Jiujiang Key Research and Development Program
- 2024 Key Research Platforms and Projects for Universities in Guangdong Province
- 2024 University Research Project of Guangzhou Education Bureau
- Guangdong Provincial Science and Technology Innovation Fund Projects
- Yangjiang Alloy Materials and Hardware Knives and Scissors Key Industry Talent Revitalization Plan Special Foundation
- 2025 Guangzhou Municipal Teaching Reform Project for Higher Education
- Guangdong Educational Science Planning Project
Zitieren
APA
Liu, Y., Li, G., Xu, R., Liang, H., Ma, N., & Zhang, Z. (2026). Study on the Wear Resistance of Laser Cladding h-BN Reinforced by TiCN/Ni-Based Coating on TC4 Alloy Surface. Coatings, 16(4), 490. https://doi.org/10.3390/coatings16040490
Vancouver
Liu Y, Li G, Xu R, Liang H, Ma N, Zhang Z. Study on the Wear Resistance of Laser Cladding h-BN Reinforced by TiCN/Ni-Based Coating on TC4 Alloy Surface. Coatings. 2026;16(4):490. doi:10.3390/coatings16040490
BibTeX
@article{Liu2026,
author = {Liu, Yu and Li, Guohui and Xu, Ruoyu and Liang, Hui and Ma, Nan and Zhang, Zhanhui},
title = {Study on the Wear Resistance of Laser Cladding h-BN Reinforced by TiCN/Ni-Based Coating on TC4 Alloy Surface},
journal = {Coatings},
year = {2026},
volume = {16},
number = {4},
pages = {490},
doi = {10.3390/coatings16040490}
}
EUVIMED