EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Arc Current on the Microstructure of AlTiN-Coated Tools and Milling of 304 Stainless Steel

Simin Zou, Zixiang Luo, Yingxin Li, Liang Yuan, Yu Tang, Jialin Zhou, Huizhong Li

Coatings · 04.06.2024 · 14 (6) · 704

DOI: 10.3390/coatings14060704 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 04.06.2024. Verfasst von Simin Zou und 6 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Hunan Key Research and Developments Program, Science and Technology Innovation Talent Program.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

304 stainless steel demonstrates a low thermal conductivity and work hardening characteristics, resulting in its processing, and will adhere to the tip of the tool; as well as the phenomenon of chipping, shortening the life of the tool. AlTiN coatings are representative of coatings applied to carbide tools. In this paper, AlTiN coatings with different arc current processes were deposited on carbide milling inserts using arc ion plating. The microstructure, mechanical properties, and milling properties of the coatings were investigated by using the SEM, EDS, XRD, scratch meter, friction and wear meter, and vertical machining center. The findings revealed that all coatings displayed columnar crystal growth, free from cracks and voids. With an increasing arc current, there was a notable increase in surface droplets, pits, and coating thickness. The coating deposited at a 140 A arc current showed a pronounced (200) orientation preference. The adhesion force peaked at 56.0 N with a subsequent decline, and the friction coefficient hit its lowest point of 0.429 at 140 A, contrasting with its highest value of 0.55 at 160 A. After 39 min of dry milling, the tool with a 140 A AlTiN coating exhibited minimal wear of 0.196 mm, just below the 0.2 mm failure threshold, indicating superior performance at this arc current setting.

Förderung

  • Hunan Key Research and Developments Program
  • Science and Technology Innovation Talent Program

Zitieren

APA

Zou, S., Luo, Z., Li, Y., Yuan, L., Tang, Y., Zhou, J., & Li, H. (2024). Effect of Arc Current on the Microstructure of AlTiN-Coated Tools and Milling of 304 Stainless Steel. Coatings, 14(6), 704. https://doi.org/10.3390/coatings14060704

Vancouver

Zou S, Luo Z, Li Y, Yuan L, Tang Y, Zhou J, et al. Effect of Arc Current on the Microstructure of AlTiN-Coated Tools and Milling of 304 Stainless Steel. Coatings. 2024;14(6):704. doi:10.3390/coatings14060704

BibTeX
@article{Zou2024,
  author = {Zou, Simin and Luo, Zixiang and Li, Yingxin and Yuan, Liang and Tang, Yu and Zhou, Jialin and Li, Huizhong},
  title = {Effect of Arc Current on the Microstructure of AlTiN-Coated Tools and Milling of 304 Stainless Steel},
  journal = {Coatings},
  year = {2024},
  volume = {14},
  number = {6},
  pages = {704},
  doi = {10.3390/coatings14060704}
}
Kostenlos starten →