EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Effect of Laser Shock Peening (LSP) on the Surface Roughness and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Alloy

Krista Dyer, Samira Ghadar, Sanin Zulić, Danijela Rostohar, Ebrahim Asadi, Reza Molaei

Coatings · 15.01.2024 · 14 (1) · 110

DOI: 10.3390/coatings14010110 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 15.01.2024. Verfasst von Krista Dyer und 5 weiteren Autor:innen. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser shock peening (LSP) uses plasma shock waves to induce compressive residual stress at the surface of a component which has the potential to improve its fatigue properties. For AM parts, the existence of internal defects, surface roughness, and tensile residual stresses leads to noticeably lower fatigue strength compared to materials produced through conventional processes. Furthermore, there is a tendency for greater scatter in the fatigue behavior of these parts when compared to traditionally manufactured components. In this study, the effect of LSP on the roughness and fatigue behavior of Ti-6Al-4V alloy constructed through Laser Powder Bed Fusion (L-PBF) technique was investigated. Two types of samples were designed and tested: as-built surface air foil samples for four-point bending tests and machined surface straight gage samples for uniaxial fatigue testing. Two sets of process parameters, optimized and non-optimized, were also used for the fabrication of each sample type. It was found that LSP had negative effects on the smooth (i.e., machined) surface samples, whereas for as-built surfaces the roughness was enhanced by decreasing the sharpness of the deep valleys and partially remelting the loosely bonded particles on the peaks. It was found that the scatter of the fatigue data decreased for optimized machined samples, while no clear improvement was observed in their lives. However, all non-optimized samples showed improvements in fatigue lives after the LSP process.

Zitieren

APA

Dyer, K., Ghadar, S., Zulić, S., Rostohar, D., Asadi, E., & Molaei, R. (2024). The Effect of Laser Shock Peening (LSP) on the Surface Roughness and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Alloy. Coatings, 14(1), 110. https://doi.org/10.3390/coatings14010110

Vancouver

Dyer K, Ghadar S, Zulić S, Rostohar D, Asadi E, Molaei R. The Effect of Laser Shock Peening (LSP) on the Surface Roughness and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Alloy. Coatings. 2024;14(1):110. doi:10.3390/coatings14010110

BibTeX
@article{Dyer2024,
  author = {Dyer, Krista and Ghadar, Samira and Zulić, Sanin and Rostohar, Danijela and Asadi, Ebrahim and Molaei, Reza},
  title = {The Effect of Laser Shock Peening (LSP) on the Surface Roughness and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Alloy},
  journal = {Coatings},
  year = {2024},
  volume = {14},
  number = {1},
  pages = {110},
  doi = {10.3390/coatings14010110}
}
Kostenlos starten →