Optimization of Yb:CaF2 Transparent Ceramics by Air Pre-Sintering and Hot Isostatic Pressing
Ceramics · 15.08.2024 · 7 (3) · 1053-1065
DOI: 10.3390/ceramics7030069 ↗Kurz gefasst
Fachartikel in der Zeitschrift Ceramics, online erschienen am 15.08.2024. Verfasst von Xiang Li und 10 weiteren Autor:innen. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key R&D Program of China, International Partnership Program of Chinese Academy of Sciences, National Center for Research and Development.
Abstract (Originalsprache)
Yb:CaF2 transparent ceramics represent a promising laser gain medium for ultra-short lasers due to their characteristics: low phonon energy, relatively high thermal conductivity, negative thermo-optical coefficient, and low refractive index. Compared to single crystals, Yb:CaF2 ceramics offer superior mechanical properties, lower cost, and it is easier to obtain large-sized samples with proper shape and uniform Yb3+ doping at high concentrations. The combination of air pre-sintering and Hot Isostatic Pressing (HIP) emerges as a viable strategy for achieving high optical quality and fine-grained structure of ceramics at lower sintering temperatures. The properties of the powders used in ceramic fabrication critically influence both optical quality and laser performance of Yb:CaF2 ceramics. In this study, the 5 atomic percentage (at.%) Yb:CaF2 transparent ceramics were fabricated by air pre-sintering and hot isostatic pressing (HIP) using nano-powders synthesized through the co-precipitation method. The co-precipitated powders were optimized by studying air calcination temperature (from 350 to 550 °C). The influence of calcination temperature on the microstructure and laser performance of Yb:CaF2 ceramics was studied in detail. The 5 at.% Yb:CaF2 transparent ceramics air pre-sintered at 625 °C from powders air calcined at 400 °C and HIP post-treated at 600 °C exhibited the highest in-line transmittance of 91.5% at 1200 nm (3.0 mm thickness) and the best laser performance. Specifically, a maximum output power of 0.47 W with a maximum slope efficiency of 9.2% at 1029 nm under quasi-CW (QCW) pumping was measured.
Förderung
- National Key R&D Program of China
- International Partnership Program of Chinese Academy of Sciences
- National Center for Research and Development
- Chinese Academy of Sciences President’s International Fellowship Initiative
Zitieren
APA
Li, X., Hu, C., Guo, L., Wu, J., Toci, G., Pirri, A., Patrizi, B., Vannini, M., Liu, Q., Hreniak, D., & Li, J. (2024). Optimization of Yb:CaF2 Transparent Ceramics by Air Pre-Sintering and Hot Isostatic Pressing. Ceramics, 7(3), 1053-1065. https://doi.org/10.3390/ceramics7030069
Vancouver
Li X, Hu C, Guo L, Wu J, Toci G, Pirri A, et al. Optimization of Yb:CaF2 Transparent Ceramics by Air Pre-Sintering and Hot Isostatic Pressing. Ceramics. 2024;7(3):1053-1065. doi:10.3390/ceramics7030069
BibTeX
@article{Li2024,
author = {Li, Xiang and Hu, Chen and Guo, Lihao and Wu, Junlin and Toci, Guido and Pirri, Angela and Patrizi, Barbara and Vannini, Matteo and Liu, Qiang and Hreniak, Dariusz and Li, Jiang},
title = {Optimization of Yb:CaF2 Transparent Ceramics by Air Pre-Sintering and Hot Isostatic Pressing},
journal = {Ceramics},
year = {2024},
volume = {7},
number = {3},
pages = {1053--1065},
doi = {10.3390/ceramics7030069}
}
EUVIMED