EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Facile Surface Modification Strategy for Antibody Immobilization on 3D-Printed Surfaces

Brandi Binkley iD, Peng Li iD

Biosensors · 2025

DOI: 10.3390/bios15040211 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biosensors, 2025. Verfasst von Brandi Binkley und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, West Virginia University, Morgantown, WV 26506, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Antibodies, Immobilized, Biosensing Techniques. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Division of Electrical, Communications & Cyber Systems, National Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D-printed microdevices have become increasingly important to the advancement of point-of-care (POC) immunoassays. Despite its great potential, using 3D-printed surfaces on the solid support for immunorecognition has been limited due to the non-ideal adsorption properties for many photocurable resins. In this work, we report a simple surface modification protocol that works for diverse commercial photocurable resins, improving ELISAs performed directly on 3D-printed devices. This surface modification strategy involves surface activation via air plasma followed by the one-step incubation of GLYMO-labeled streptavidin. We successfully immobilized biotinylated anti-activin A antibodies on the 3D-printed surfaces and performed the complete ELISA protocol on the 3D-printed surfaces. We demonstrated that this protocol achieved an improved performance over passive adsorption for ELISAs. The present method is also compatible with diverse commercial resins and works with both microwells and microchannels. Finally, this method demonstrated a comparable limit of detection to the ELISA performed using commercial microwells. We believe the simplicity and broad compatibility of the present surface modification strategy will facilitate the development of 3D-printed POC ELISA devices.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalAntibodies, ImmobilizedBiosensing TechniquesSurface PropertiesEnzyme-Linked Immunosorbent AssayAdsorptionImmunoassay

Stichwörter der Autor:innen

3D printingELISAsurface modification

Substanzen

Antibodies, Immobilized

Autor:innen und Institutionen

  • Department of Chemistry, West Virginia University, Morgantown, WV 26506, USA.

ORCID-Profile: Brandi Binkley, Peng Li

Förderung

  • Division of Electrical, Communications & Cyber Systems
  • National Science Foundation

Zitieren

APA

Binkley, B., & Li, P. (2025). A Facile Surface Modification Strategy for Antibody Immobilization on 3D-Printed Surfaces. Biosensors. https://doi.org/10.3390/bios15040211

Vancouver

Binkley B, Li P. A Facile Surface Modification Strategy for Antibody Immobilization on 3D-Printed Surfaces. Biosensors. 2025. doi:10.3390/bios15040211

BibTeX
@article{Binkley2025,
  author = {Binkley, Brandi and Li, Peng},
  title = {A Facile Surface Modification Strategy for Antibody Immobilization on 3D-Printed Surfaces},
  journal = {Biosensors},
  year = {2025},
  doi = {10.3390/bios15040211}
}
Kostenlos starten →