Surface Acoustic Wave (SAW) Sensors for Hip Implant: A Numerical and Computational Feasibility Investigation Using Finite Element Methods
Biosensors · 2023
DOI: 10.3390/bios13010079 ↗Kurz gefasst
Fachartikel in der Zeitschrift Biosensors, 2023. Verfasst von Muhammad Hafizh und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Industrial Engineering, Qatar University, Doha 2713, Qatar. Hauptthemen laut MEDLINE: Hip Prosthesis, Arthroplasty, Replacement, Hip. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Qatar National Research Fund, APC.
Abstract (Originalsprache)
In this paper, a surface acoustic wave (SAW) sensor for hip implant geometry was proposed for the application of total hip replacement. A two-port SAW device was numerically investigated for implementation with an operating frequency of 872 MHz that can be used in more common radio frequency interrogator units. A finite element analysis of the device was developed for a lithium niobate (LiNBO3) substrate with a Rayleigh velocity of 3488 m/s on COMSOL Multiphysics. The Multiphysics loading and frequency results highlighted a good uniformity with numerical results. Afterwards, a hip implant geometry was developed. The SAW sensor was mounted at two locations on the implant corresponding to two regions along the shaft of the femur bone. Three discrete conditions were studied for the feasibility of the implant with upper- and lower-body loading. The loading simulations highlighted that the stresses experienced do not exceed the yield strengths. The voltage output results indicated that the SAW sensor can be implanted in the hip implant for hip implant-loosening detection applications.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Mechanical and Industrial Engineering, Qatar University, Doha 2713, Qatar.
- Department of Electrical, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia.
- Department of Electrical Engineering, Qatar University, Doha 2713, Qatar.
- Centre for Advanced Electronic and Communication Engineering, Department of Electrical, Electronic and Systems Engineering, Faculty of Engineering & Built Environment, Universiti Kebangsaan Malaysia (UKM), Bangi 43600,…
- Department of Biomedical Engineering, University of Texas at San Antonio, San Antonio, TX 78249, USA.
ORCID-Profile: Muhammad Hafizh, Md Mohiuddin Soliman, Muhammad E H Chowdhury, Mohammad Tariqul Islam, Farayi Musharavati, Sakib Mahmud, Amith Khandakar
Förderung
- Qatar National Research Fund
- APC
Zitieren
APA
Hafizh, M., Soliman, M. M., Qiblawey, Y., Chowdhury, M. E. H., Islam, M. T., Musharavati, F., Mahmud, S., Khandakar, A., Nabil, M., & Nezhad, E. Z. (2023). Surface Acoustic Wave (SAW) Sensors for Hip Implant: A Numerical and Computational Feasibility Investigation Using Finite Element Methods. Biosensors. https://doi.org/10.3390/bios13010079
Vancouver
Hafizh M, Soliman MM, Qiblawey Y, Chowdhury MEH, Islam MT, Musharavati F, et al. Surface Acoustic Wave (SAW) Sensors for Hip Implant: A Numerical and Computational Feasibility Investigation Using Finite Element Methods. Biosensors. 2023. doi:10.3390/bios13010079
BibTeX
@article{Hafizh2023,
author = {Hafizh, Muhammad and Soliman, Md Mohiuddin and Qiblawey, Yazan and Chowdhury, Muhammad E H and Islam, Mohammad Tariqul and Musharavati, Farayi and Mahmud, Sakib and Khandakar, Amith and Nabil, Mohammad and Nezhad, Erfan Zal},
title = {Surface Acoustic Wave (SAW) Sensors for Hip Implant: A Numerical and Computational Feasibility Investigation Using Finite Element Methods},
journal = {Biosensors},
year = {2023},
doi = {10.3390/bios13010079}
}
EUVIMED