EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Numerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens

Riza Gabdyssalyk, Daulet Zhamsap, Samat Baigereyev, Karibek Sherov, Alfiya Muzdybayeva, Tatyana Brim

Applied Mechanics · 15.11.2026 · 7 (4) · 98

DOI: 10.3390/applmech7040098 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Mechanics, online erschienen am 15.11.2026. Verfasst von Riza Gabdyssalyk und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Hardfacing is widely used to restore worn gate-valve surfaces, but the choice of process parameters must account for residual stress, distortion, plastic strain, and the heat-affected zone (HAZ). This study investigated the hardfacing of 09G2S steel numerically in Simufact Welding using a Taguchi L9 design for three filler materials, Np-65G, Stoodite 6M, and PrNl-3V14K, giving 27 simulated conditions. The Goldak heat source was calibrated against a theoretical penetration depth of 1.2–1.5 mm. Conditions resulting in metal boiling, an unmelted bead center, or a penetration depth outside 1.0–2.0 mm were excluded. Lower residual stresses were obtained only together with insufficient penetration or overheating. Run 6 was selected for Np-65G (285 MPa; HAZ depth, 4.7 mm) and Stoodite 6M (373 MPa; 4.6 mm), and Run 2 for PrNl-3V14K (289 MPa; 3.5 mm). On a model of a 90-mm-thick gate plate, the selected Np-65G condition gave a penetration depth of only about 0.5 mm; an adjusted condition within the investigated levels (160 A, 12 V, 3 m/h, 200 °C) gave 1.45–1.80 mm with a fully melted bead for both Np-65G and Stoodite 6M. Conditions selected on specimens must therefore be reassessed for the actual component. Specimens hardfaced under industrial conditions were characterized by microscopy and microhardness testing: 386–466 HV0.05 for the Stoodite 6M deposit and 345–440 HV0.05 for Np-65G.

Förderung

  • Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Gabdyssalyk, R., Zhamsap, D., Baigereyev, S., Sherov, K., Muzdybayeva, A., & Brim, T. (2026). Numerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens. Applied Mechanics, 7(4), 98. https://doi.org/10.3390/applmech7040098

Vancouver

Gabdyssalyk R, Zhamsap D, Baigereyev S, Sherov K, Muzdybayeva A, Brim T. Numerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens. Applied Mechanics. 2026;7(4):98. doi:10.3390/applmech7040098

BibTeX
@article{Gabdyssalyk2026,
  author = {Gabdyssalyk, Riza and Zhamsap, Daulet and Baigereyev, Samat and Sherov, Karibek and Muzdybayeva, Alfiya and Brim, Tatyana},
  title = {Numerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens},
  journal = {Applied Mechanics},
  year = {2026},
  volume = {7},
  number = {4},
  pages = {98},
  doi = {10.3390/applmech7040098}
}
Kostenlos starten →