EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparison of surface integrity, longevity of posterior tooth-colored crowns fabricated by conventional, CAD/CAM, and 3D printing techniques

Tanner Hunt, Jacob Nichols, Preston Harmon, Neamat Hassan Abubakr

Frontiers in Dental Medicine · 18.08.2026 · 7

DOI: 10.3389/fdmed.2026.1900498 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Dental Medicine, online erschienen am 18.08.2026. Verfasst von Tanner Hunt und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Dental Medicine, University of Nevada, Las Vegas, NV, United States. Die Arbeit nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

This in vitro study evaluated internal and marginal surface roughness and simulated thermocycling survival of posterior tooth-colored crowns fabricated using conventional laboratory, CAD/CAM milling, and digital light processing 3D printing workflows.

Methods

The roughness analysis included 46 crowns allocated to six groups: lab-made crowns ( n = 6), IPS e.max CAD ( n = 8), IPS Empress CAD ( n = 8), Lava Ultimate ( n = 8), IPS e.max ZirCAD ( n = 8), and 3 D SprintRay Ceramic ( n = 8). Internal and marginal arithmetic mean roughness (Ra, µm) were measured with a 3D non-contact profilometer. Because residual normality and variance homogeneity assumptions were not satisfied, group differences were analyzed using Kruskal–Wallis tests followed by Holm-adjusted pairwise Mann–Whitney U tests.

Results

Internal Ra differed significantly among groups ( H = 25.76, df = 5, p < 0.001). 3D printed SprintRay Ceramic showed the highest internal Ra (29.27 ± 5.45 µm) and was significantly rougher internally than every other group after Holm correction. Marginal Ra also differed significantly among groups ( H = 41.86, df = 5, p < 0.001). IPS e.max CAD showed the highest marginal Ra (26.81 ± 1.73 µm), followed by lab-made crowns (19.31 ± 6.40 µm), whereas IPS e.max ZirCAD showed the lowest marginal Ra (4.82 ± 1.03 µm).

Conclusion

Within the limitation of the present study material type and fabrication workflow significantly influenced internal and marginal surface roughness of posterior tooth-colored crowns. The crowns survival rates were more closely associated with material type than fabrication method.

Schlagwörter

Stichwörter der Autor:innen

3D printing ceramicCAD/CAMposterior crownssurface roughnesssurvival rate

Autor:innen und Institutionen

  • School of Dental Medicine, University of Nevada, Las Vegas, NV, United States.
  • Biomedical Sciences Department, School of Dental Medicine, University of Nevada, Las Vegas, NV, United States.

Zitieren

APA

Hunt, T., Nichols, J., Harmon, P., & Abubakr, N. H. (2026). Comparison of surface integrity, longevity of posterior tooth-colored crowns fabricated by conventional, CAD/CAM, and 3D printing techniques. Frontiers in Dental Medicine, 7. https://doi.org/10.3389/fdmed.2026.1900498

Vancouver

Hunt T, Nichols J, Harmon P, Abubakr NH. Comparison of surface integrity, longevity of posterior tooth-colored crowns fabricated by conventional, CAD/CAM, and 3D printing techniques. Frontiers in Dental Medicine. 2026;7. doi:10.3389/fdmed.2026.1900498

BibTeX
@article{Hunt2026,
  author = {Hunt, Tanner and Nichols, Jacob and Harmon, Preston and Abubakr, Neamat Hassan},
  title = {Comparison of surface integrity, longevity of posterior tooth-colored crowns fabricated by conventional, CAD/CAM, and 3D printing techniques},
  journal = {Frontiers in Dental Medicine},
  year = {2026},
  volume = {7},
  doi = {10.3389/fdmed.2026.1900498}
}
Kostenlos starten →