EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Design of novel orthotic insoles based on partition infilling of TPMS structures

Yongtao Lyu, Lingqi Meng, Hao Wang, Zihao Wang, Lingyi Cong, Sergei Bosiakov, Yuanfei Ren

Frontiers in Bioengineering and Biotechnology · 01.05.2026 · 14

DOI: 10.3389/fbioe.2026.1820362 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Bioengineering and Biotechnology, online erschienen am 01.05.2026. Verfasst von Yongtao Lyu und 6 weiteren Autor:innen. Beteiligte Einrichtung: The first Department of Hand and Foot Surgery, Central Hospital of Dalian University of Technology, Dalian, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Excessive plantar pressure has been recognized as a key risk factor for diabetic foot ulceration.

Methods

To address this problem, a partition-infilled functional insole based on triply periodic minimal surface (TPMS) lattice structures was proposed and systematically investigated. First, the mechanical responses of three representative TPMS structures, namely Gyroid, Diamond and Primitive, were characterized by compression experiments and finite element (FE) analysis. Subsequently, a partition infilling strategy was designed according to distribution of the plantar pressure. Under additive manufacturing constraint of minimal thickness of 0.2 mm, different TPMS lattices were assigned to specific plantar regions.

Results

Gait experiments and FE results demonstrated that, compared to a uniformly Gyroid-infilled insole and a single-lattice gradient-infilled insole, the partition-infilled insole achieved significant reductions in both peak and mean pressures. A Primitive lattice in the heel region exhibited superior pressure-relief performance, whereas Gyroid and Diamond lattices in the forefoot and midfoot balanced cushioning with overall structural stability. Owing to the mathematical definitions of different TPMS structures, smooth topological transitions between lattices were enabled, further improving comfort and manufacture ability. An integrated design-manufacturing framework for personalized diabetic insoles was established.

Discussion

The potential of TPMS partition infilling for redistributing plantar loads and reducing ulceration risk was verified, providing theoretical and experimental support for subsequent clinical applications and large-scale additive manufacturing.

Schlagwörter

Stichwörter der Autor:innen

diamondgyroidorthotic insolespartition infillingprimitive

Autor:innen und Institutionen

  • The first Department of Hand and Foot Surgery, Central Hospital of Dalian University of Technology, Dalian, China.
  • DUT-BSU Joint Institute, Dalian University of Technology, Dalian, China.
  • Department of Engineering Mechanics, Dalian University of Technology, Dalian, China.
  • Faculty of Mechanics and Mathematics, Belarusian State University, Minsk, Belarus.

Zitieren

APA

Lyu, Y., Meng, L., Wang, H., Wang, Z., Cong, L., Bosiakov, S., & Ren, Y. (2026). Design of novel orthotic insoles based on partition infilling of TPMS structures. Frontiers in Bioengineering and Biotechnology, 14. https://doi.org/10.3389/fbioe.2026.1820362

Vancouver

Lyu Y, Meng L, Wang H, Wang Z, Cong L, Bosiakov S, et al. Design of novel orthotic insoles based on partition infilling of TPMS structures. Frontiers in Bioengineering and Biotechnology. 2026;14. doi:10.3389/fbioe.2026.1820362

BibTeX
@article{Lyu2026,
  author = {Lyu, Yongtao and Meng, Lingqi and Wang, Hao and Wang, Zihao and Cong, Lingyi and Bosiakov, Sergei and Ren, Yuanfei},
  title = {Design of novel orthotic insoles based on partition infilling of TPMS structures},
  journal = {Frontiers in Bioengineering and Biotechnology},
  year = {2026},
  volume = {14},
  doi = {10.3389/fbioe.2026.1820362}
}
Kostenlos starten →