3D printed β-tricalcium phosphate versus synthetic bone mineral scaffolds: A comparative in vitro study of biocompatibility
Bio-Medical Materials and Engineering · 2024
DOI: 10.3233/bme-230214 ↗At a glance
Vergleichsstudie in Bio-Medical Materials and Engineering, 2024. Written by Blaire V Slavin and 10 co-authors. Institution: Miller School of Medicine, University of Miami, Miami, FL, USA. Major MEDLINE topics: Calcium Phosphates, Printing, Three-Dimensional, Tissue Scaffolds, Materials Testing. Cited 3 times so far (Crossref); 50 references.
Abstract (original language)
BACKGROUND: β-tricalcium phosphate (β-TCP) has been successfully utilized as a 3D printed ceramic scaffold in the repair of non-healing bone defects; however, it requires the addition of growth factors to augment its regenerative capacity. Synthetic bone mineral (SBM) is a novel and extrudable carbonate hydroxyapatite with ionic substitutions known to facilitate bone healing. However, its efficacy as a 3D printed scaffold for hard tissue defect repair has not been explored. OBJECTIVE: To evaluate the biocompatibility and cell viability of human osteoprecursor (hOP) cells seeded on 3D printed SBM scaffolds via in vitro analysis. METHODS: SBM and β-TCP scaffolds were fabricated via 3D printing and sintered at various temperatures. Scaffolds were then subject to qualitative cytotoxicity testing and cell proliferation experiments utilizing (hOP) cells. RESULTS: SBM scaffolds sintered at lower temperatures (600 °C and 700 °C) induced greater levels of acute cellular stress. At higher sintering temperatures (1100 °C), SBM scaffolds showed inferior cellular viability relative to β-TCP scaffolds sintered to the same temperature (1100 °C). However, qualitative analysis suggested that β-TCP presented no evidence of morphological change, while SBM 1100 °C showed few instances of acute cellular stress. CONCLUSION: Results demonstrate SBM may be a promising alternative to β-TCP for potential applications in bone tissue engineering.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Miller School of Medicine, University of Miami, Miami, FL, USA.
- Department of Biochemistry and Molecular Biology, Miller School of Medicine, University of Miami, Miami, FL, USA.
- School of Materials Science and Engineering, Oklahoma State University, Tulsa, OK, USA.
- Division of Vascular and Endovascular Surgery, Department of Surgery and Cell Biology, Langone Medical Center, New York University, New York, NY, USA.
- Biomaterials Division, NYU College of Dentistry, New York, NY, USA.
- DeWitt Daughtry Family Department of Surgery, Division of Plastic Surgery, Miller School of Medicine, University of Miami, Miami, FL, USA.
Cite
APA
Slavin, B. V., Mirsky, N. A., Stauber, Z. M., Nayak, V. V., Smay, J. E., Rivera, C. F., Mijares, D. Q., Coelho, P. G., Cronstein, B. N., Tovar, N., & Witek, L. (2024). 3D printed β-tricalcium phosphate versus synthetic bone mineral scaffolds: A comparative in vitro study of biocompatibility. Bio-Medical Materials and Engineering. https://doi.org/10.3233/bme-230214
Vancouver
Slavin BV, Mirsky NA, Stauber ZM, Nayak VV, Smay JE, Rivera CF, et al. 3D printed β-tricalcium phosphate versus synthetic bone mineral scaffolds: A comparative in vitro study of biocompatibility. Bio-Medical Materials and Engineering. 2024. doi:10.3233/bme-230214
BibTeX
@article{Slavin2024,
author = {Slavin, Blaire V and Mirsky, Nicholas A and Stauber, Zachary M and Nayak, Vasudev Vivekanand and Smay, James E and Rivera, Cristobal F and Mijares, Dindo Q and Coelho, Paulo G and Cronstein, Bruce N and Tovar, Nick and Witek, Lukasz},
title = {3D printed β-tricalcium phosphate versus synthetic bone mineral scaffolds: A comparative in vitro study of biocompatibility},
journal = {Bio-Medical Materials and Engineering},
year = {2024},
doi = {10.3233/bme-230214}
}
EUVIMED