TOOL WEAR AND VIBRATION ANALYSIS IN CNC TURNING OF STAINLESS STEEL 304 USING CARBIDE INSERTS WITH VARYING CUTTING PARAMETERS
JOURNAL OF SCIENCE AND APPLIED ENGINEERING · 26.10.2026 · 9 (2) · 72-79
DOI: 10.31328/jsae.v9i2.7668 ↗Kurz gefasst
Fachartikel in der Zeitschrift JOURNAL OF SCIENCE AND APPLIED ENGINEERING, online erschienen am 26.10.2026. Verfasst von Mas Achmad Yusuf Wibisono und 2 weiteren Autor:innen.
Abstract (Originalsprache)
This study examines end point flank wear and recorded acceleration during CNC turning of Stainless Steel 304 (SS304) using carbide inserts and a Taguchi L9 design. Originality/value: It considers low-cost accelerometer readings alongside direct post-trial wear observations for nine cutting-parameter combinations. Design/methodology/approach: Cutting speed (80, 120, and 160 m/min), feed rate (0.05, 0.10, and 0.15 mm/rev), and depth of cut (0.3, 0.6, and 1.0 mm) were varied. Flank wear was inspected using a digital microscope. The supplied recorded RMS values were 1.20–3.65 m/s². Acceleration was reported as sampled at 2 Hz, equivalent to a 1 Hz Nyquist limit. Each L9 combination was run once. Research limitations/implications: Three trials (3, 5, and 8) ended in tool damage or incomplete machining. Trial 5's recorded VB value of zero was therefore treated as unavailable, not as zero wear. The dataset has no replication, and calibration, offset correction, and filtering were not documented. Consequently, the RMS values cannot be considered validated measurements of cutting vibration, and statistical significance or failure thresholds cannot be established. Results/Findings: Among successful trials, end-point VB ranged from 0.041 to 0.075 mm. Trials 3 and 8 also had recorded VB readings of 0.181 and 0.136 mm, respectively, but both ended in chipping/incomplete machining. Exploratory smaller-is-better Taguchi calculations were updated using the supplied values, with Trial 5 excluded from continuous-VB S/N calculations and retained for RMS analysis. Conclusion: The results are descriptive and identify candidates for confirmation rather than a validated optimum. Replicated trials, calibrated high-rate vibration acquisition, and wear measurements normalized by cutting time or length are needed.
Zitieren
APA
Wibisono, M. A. Y., Hendra, & Dwinanto (2026). TOOL WEAR AND VIBRATION ANALYSIS IN CNC TURNING OF STAINLESS STEEL 304 USING CARBIDE INSERTS WITH VARYING CUTTING PARAMETERS. JOURNAL OF SCIENCE AND APPLIED ENGINEERING, 9(2), 72-79. https://doi.org/10.31328/jsae.v9i2.7668
Vancouver
Wibisono MAY, Hendra, Dwinanto. TOOL WEAR AND VIBRATION ANALYSIS IN CNC TURNING OF STAINLESS STEEL 304 USING CARBIDE INSERTS WITH VARYING CUTTING PARAMETERS. JOURNAL OF SCIENCE AND APPLIED ENGINEERING. 2026;9(2):72-79. doi:10.31328/jsae.v9i2.7668
BibTeX
@article{Wibisono2026,
author = {Wibisono, Mas Achmad Yusuf and Hendra and Dwinanto},
title = {TOOL WEAR AND VIBRATION ANALYSIS IN CNC TURNING OF STAINLESS STEEL 304 USING CARBIDE INSERTS WITH VARYING CUTTING PARAMETERS},
journal = {JOURNAL OF SCIENCE AND APPLIED ENGINEERING},
year = {2026},
volume = {9},
number = {2},
pages = {72--79},
doi = {10.31328/jsae.v9i2.7668}
}
EUVIMED