EUVIMEDEUVIMED entdecken
Crossref

Comparative evaluation of dental measurements using 3D virtual models and 3D printed models

Anju Treesa Jacob, Achint Juneja, Monis Raza, Nivedita Sharma, Ridhi Kothari

APOS Trends in Orthodontics · 19.11.2025 · 16 · 208-215

DOI: 10.25259/apos_240_2024 ↗

Kurz gefasst

Fachartikel in der Zeitschrift APOS Trends in Orthodontics, online erschienen am 19.11.2025. Verfasst von Anju Treesa Jacob und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 20 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

Accurate dental measurements are essential for orthodontic diagnosis, treatment planning, and long-term patient monitoring. With the increased use of digital workflows, 3D virtual models and 3D printed models are being adopted as alternatives to traditional plaster casts. This study aimed to evaluate and compare key orthodontic dental parameters obtained from 3D virtual models and 3D printed models to determine their reliability and potential for clinical interchangeability. Material and Methods: Seventeen pre-treatment intraoral scans (iTero, Align Technology, USA) meeting the inclusion criteria were analyzed. The scans were divided into three groups: Group A – 3D virtual models assessed using GOM Inspect software; Group B – 3D virtual models assessed using OrthoCAD software; and Group C – corresponding 3D printed models fabricated using a Phrozen Sonic Mighty 4K printer and evaluated with dental loupes and Vernier calipers. Measured parameters included maxillary and mandibular intercanine widths, intermolar widths, overjet, overbite, and Bolton’s overall and anterior ratios. Normality was assessed with the Shapiro–Wilk test. One-way analysis of variance was used for intergroup comparisons, Pearson’s correlation tested associations between methods, and the intraclass correlation coefficient (ICC) determined reproducibility.

Results

All measurements followed a normal distribution. No statistically significant differences were found among the three groups for any parameter ( p > 0.05). For example, the mean maxillary intercanine width was 34.19 ± 1.36 mm (Group A), 34.41 ± 1.34 mm (Group B), and 34.17 ± 1.34 mm (Group C) ( p = 0.849). Mean mandibular intermolar width was 44.83 ± 2.77 mm (Group A), 44.89 ± 2.88 mm (Group B), and 44.72 ± 2.69 mm (Group C) ( p = 0.982). Overjet and overbite showed similarly close agreement, with p = 0.999 and 1.000, respectively. ICC analysis demonstrated excellent reproducibility across all methods (ICC = 0.98). Pearson’s correlation revealed strong agreement between GOM and 3D printed models for all parameters, while OrthoCAD showed weaker correlation for sum-of-teeth measurements and Bolton’s ratios.

Conclusion

3D virtual models and 3D printed models provide equivalent and reproducible dental measurements, making them reliable alternatives to conventional plaster models for orthodontic diagnosis, treatment planning, and outcome assessment. Given their interchangeability, digital workflows can be confidently integrated into clinical practice, offering advantages in storage, accessibility, and patient communication. Future research should explore their performance in severe crowding cases, assess cost-effectiveness, and investigate optimization of software such as OrthoCAD to improve consistency.

Zitieren

APA

Jacob, A. T., Juneja, A., Raza, M., Sharma, N., & Kothari, R. (2025). Comparative evaluation of dental measurements using 3D virtual models and 3D printed models. APOS Trends in Orthodontics, 16, 208-215. https://doi.org/10.25259/apos_240_2024

Vancouver

Jacob AT, Juneja A, Raza M, Sharma N, Kothari R. Comparative evaluation of dental measurements using 3D virtual models and 3D printed models. APOS Trends in Orthodontics. 2025;16:208-215. doi:10.25259/apos_240_2024

BibTeX
@article{Jacob2025,
  author = {Jacob, Anju Treesa and Juneja, Achint and Raza, Monis and Sharma, Nivedita and Kothari, Ridhi},
  title = {Comparative evaluation of dental measurements using 3D virtual models and 3D printed models},
  journal = {APOS Trends in Orthodontics},
  year = {2025},
  volume = {16},
  pages = {208--215},
  doi = {10.25259/apos_240_2024}
}
Kostenlos starten →