EUVIMEDEUVIMED entdecken
Crossref

A Micro-computed Tomography Analysis of Marginal and Internal Fit of Endocrowns Fabricated from Three CAD/CAM Materials

L Hassouneh, A Jum'ah, M Ferrari, D J Wood

Operative Dentistry · 2023

DOI: 10.2341/21-105-l ↗

Kurz gefasst

Fachartikel in der Zeitschrift Operative Dentistry, 2023. Verfasst von L Hassouneh und 3 weiteren Autor:innen. Beteiligte Einrichtung: Layla Hassouneh, PhD, MClinDent, BDS, University of Leeds, School of Dentistry, Division of Restorative Dentistry, Leeds, UK; and Department of Conse…. Hauptthemen laut MEDLINE: Crowns, Dental Prosthesis Design. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 46 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To assess the marginal and internal misfit of endocrowns fabricated from a resin matrix ceramic (CS), a partially crystallized (EMC), and a fully crystallized (ILS) lithium disilicate glass-ceramic. Methods and Materials Thirty human premolar teeth restored with endocrowns were investigated. Three CAD/CAM materials were used (n=10 per group): CS, EMC, and ILS. Two-dimensional (2D) analysis of marginal and internal misfit was performed on micro-computed tomography scans before and after adhesive bonding. Further, three-dimensional (3D) analysis was performed to determine the total internal volume discrepancy. Surface roughness of the fitting surfaces of endocrowns was characterized using optical profilometry and scanning electron microscopy.

Results

Adhesive bonding did not significantly affect marginal or internal misfit ( p ≥0.093). Differences in marginal misfit among the experimental groups were not statistically significant ( p ≥0.221). However, differences in 2D internal misfit were statistically significant; the CS group exhibited the largest internal misfit ( p =0.001), while no significant difference was found between other groups ( p =0.123). The largest discrepancies were observed at the pulpal floor and cervical region of all investigated specimens. No statistically significant difference was found in 3D misfit between ILS and EMC groups ( p =0.711); however both exhibited statistically lower 3D misfit values compared to the CS group ( p ≤0.037). ILS endocrowns exhibited the smoothest and most homogenous fitting surface profile ( p

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsDental Prosthesis DesignHumansX-Ray MicrotomographyDental Marginal AdaptationMaterials TestingDental PorcelainCeramicsComputer-Aided Design

Substanzen

Dental Porcelain

Autor:innen und Institutionen

  • Layla Hassouneh, PhD, MClinDent, BDS, University of Leeds, School of Dentistry, Division of Restorative Dentistry, Leeds, UK; and Department of Conservative Dentistry, Faculty of Dentistry, Jordan University of Science…
  • *Ahmad Jum'ah, PhD, MRD(Pros.)RSCEd, RSCEd, JB, MSc, BDS, Department of Conservative Dentistry, Faculty of Dentistry, Jordan University of Science and Technology, Irbid, Jordan; and Faculty of Dentistry, Aqaba Medical S…
  • Marco Ferrari, MD DDS, PhD, 1. University of Siena, Department of Medical Biotechnologies, Division of Fixed Prosthodontics, Siena, Italy 2. University of Leeds, School of Dentistry, Division of Restorative Dentistry, L…
  • David J Wood, BSc, PhD, University of Leeds, School of Dentistry, Division of Oral Biology, Leeds, UK.

Zitieren

APA

Hassouneh, L., Jum'ah, A., Ferrari, M., & Wood, D. J. (2023). A Micro-computed Tomography Analysis of Marginal and Internal Fit of Endocrowns Fabricated from Three CAD/CAM Materials. Operative Dentistry. https://doi.org/10.2341/21-105-l

Vancouver

Hassouneh L, Jum'ah A, Ferrari M, Wood DJ. A Micro-computed Tomography Analysis of Marginal and Internal Fit of Endocrowns Fabricated from Three CAD/CAM Materials. Operative Dentistry. 2023. doi:10.2341/21-105-l

BibTeX
@article{Hassouneh2023,
  author = {Hassouneh, L and Jum'ah, A and Ferrari, M and Wood, D J},
  title = {A Micro-computed Tomography Analysis of Marginal and Internal Fit of Endocrowns Fabricated from Three CAD/CAM Materials},
  journal = {Operative Dentistry},
  year = {2023},
  doi = {10.2341/21-105-l}
}
Kostenlos starten →