EUVIMEDEUVIMED entdecken
Open Access · CC BY-SA 4.0

Microstructure and abrasive wear resistance in the miller test of a martensitic Fe-C alloy with V and W carbides

Grzegorz Tęcza

Journal of Mining and Metallurgy, Section B: Metallurgy · 2026 · 62 (2) · 163-176

DOI: 10.2298/jmmb251105013t ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Mining and Metallurgy, Section B: Metallurgy, 2026. Verfasst von Grzegorz Tęcza. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-SA 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A widely used material for parts and components of machines operating under abrasive wear is cast alloyed steel with medium to high carbon content, which provides sufficient hardness, along with the addition of elements such as Cr, Mn, Si, Ni, and Mo. To improve the abrasive wear resistance of the tested alloys, carbide-forming elements such as vanadium were introduced in amounts of about 18 wt.% during melting. One melt, with a total carbon content ranging from 3.4 to 3.9 wt.%, also contained 4.5 wt.% W. The measured hardness of the tested samples in the alloy with 3.4 wt% carbon, 17.7 wt% V, and 4.5 wt% W was approximately 535 HV in the as-cast state and increased to approximately 665 HV after quenching. The highest hardness was obtained for an alloy containing 3.9 wt% C and 17.9 wt% V. In the as-cast state, the hardness of this alloy was 850 HV increasing to 950 HV after quenching from 880°C and cooling in a 15% Polihartenol HI polymer solution. The microstructure of the test castings consisted of a martensitic matrix with low amounts of retained austenite, characterized by the presence of lamellar carbides with a spherical cross-section, evenly distributed in the alloy matrix. In most cases, these were \mathrm{M_2}C carbides, though in alloys with vanadium and tungsten, complex carbides of the (V,W)xCy type were also observed. The highest resistance to abrasive wear, approximately 950 HV, was achieved in a martensitic alloy with 17.9 wt% V and 0.1 wt% W, quenched from 880°C and cooled in a 15% Polihartenol HI polymer solution. Its weight loss was half that of the reference cast GX70CrMnSiNiMo2 steel.

Zitieren

APA

Tęcza, G. (2026). Microstructure and abrasive wear resistance in the miller test of a martensitic Fe-C alloy with V and W carbides. Journal of Mining and Metallurgy, Section B: Metallurgy, 62(2), 163-176. https://doi.org/10.2298/jmmb251105013t

Vancouver

Tęcza G. Microstructure and abrasive wear resistance in the miller test of a martensitic Fe-C alloy with V and W carbides. Journal of Mining and Metallurgy, Section B: Metallurgy. 2026;62(2):163-176. doi:10.2298/jmmb251105013t

BibTeX
@article{Tcza2026,
  author = {Tęcza, Grzegorz},
  title = {Microstructure and abrasive wear resistance in the miller test of a martensitic Fe-C alloy with V and W carbides},
  journal = {Journal of Mining and Metallurgy, Section B: Metallurgy},
  year = {2026},
  volume = {62},
  number = {2},
  pages = {163--176},
  doi = {10.2298/jmmb251105013t}
}
Kostenlos starten →