EUVIMEDEUVIMED entdecken
Crossref

Effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing: An in vitro study

Khin Pyae Sone, Hidekazu Takahashi, Maiko Iwaki, Sahaprom Namano, Yuriko Komagamine, Shunsuke Minakuchi, Manabu Kanazawa

Journal of Prosthodontic Research · 2024

DOI: 10.2186/jpr.jpr_d_24_00111 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2024. Verfasst von Khin Pyae Sone und 6 weiteren Autor:innen. Beteiligte Einrichtung: Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan. Hauptthemen laut MEDLINE: Hardness, Dental Restoration Wear, Tooth, Artificial, Denture Design. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 47 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: This in vitro study investigated the effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing (DLP) compared to other denture tooth materials. METHODS: Disc-shaped specimens were prepared using denture tooth monomers and DLP devices in three build orientations: 0°, 45°, and 90°. Specimens of the same shape were fabricated using denture tooth materials for subtractive manufacturing, commercially available polymethylmethacrylate (PMMA) resin, and composite resin. The wear resistance was evaluated as the wear volume loss after 50,000 wear cycles using a ball-on-disc wear device in water for two-body wear and poppy seed slurry for three-body wear. The Vickers hardness values of the materials were measured. Two-way and one-way analyses of variance were performed for wear resistance and hardness, respectively, followed by Tukey's honest significance test. RESULTS: The interaction between the denture tooth resins and maximum wear volume was significant (P < 0.01). The 0° build orientation exhibited the lowest wear volume in the three-body wear test and the highest hardness among the three build orientations. The 0° DLP-fabricated specimens demonstrated significantly less wear volume than that of the PMMA specimens and a wear volume comparable to that of the milled specimens. However, the 0° DLP-fabricated specimens showed significantly lower hardness than that of the milled and PMMA specimens. The composite resin specimens exhibited the highest wear resistance and hardness. CONCLUSIONS: A 0° build orientation is recommended for DLP-fabricated denture teeth compared to 45° and 90° orientations to achieve greater wear resistance and hardness.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

HardnessDental Restoration WearTooth, ArtificialDenture DesignDental MaterialsPolymethyl MethacrylateIn Vitro TechniquesComposite ResinsMaterials TestingHumans

Stichwörter der Autor:innen

Build orientationsDigital dentistryDigital light processingHardnessWear resistance

Substanzen

Polymethyl MethacrylateComposite ResinsDental Materials

Autor:innen und Institutionen

  • Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • School of Oral Health Engineering, Faculty of Dentistry, Tokyo Medical and Dental University, Tokyo, Japan.
  • Digital Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Clinic of General, Special Care and Geriatric Dentistry, Center for Dental Medicine, University of Zurich, Zurich, Switzerland.

Zitieren

APA

Sone, K. P., Takahashi, H., Iwaki, M., Namano, S., Komagamine, Y., Minakuchi, S., & Kanazawa, M. (2024). Effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing: An in vitro study. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_24_00111

Vancouver

Sone KP, Takahashi H, Iwaki M, Namano S, Komagamine Y, Minakuchi S, et al. Effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing: An in vitro study. Journal of Prosthodontic Research. 2024. doi:10.2186/jpr.jpr_d_24_00111

BibTeX
@article{Sone2024,
  author = {Sone, Khin Pyae and Takahashi, Hidekazu and Iwaki, Maiko and Namano, Sahaprom and Komagamine, Yuriko and Minakuchi, Shunsuke and Kanazawa, Manabu},
  title = {Effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing: An in vitro study},
  journal = {Journal of Prosthodontic Research},
  year = {2024},
  doi = {10.2186/jpr.jpr_d_24_00111}
}
Kostenlos starten →