EUVIMEDEUVIMED entdecken
Fallbericht

A dual composite resin injection molding technique with 3D-printed flexible indices for biomimetic replacement of a missing mandibular lateral incisor

Keiichiro Watanabe, Eiji Tanaka, Kohei Kamoi, Antonin Tichy, Takahiko Shiba, Kazuhide Yonerakura, Masatoshi Nakajima, Ruonan Han, Keiichi Hosaka

Journal of Prosthodontic Research · 2024

DOI: 10.2186/jpr.jpr_d_23_00239 ↗

Kurz gefasst

Fallbericht in der Zeitschrift Journal of Prosthodontic Research, 2024. Verfasst von Keiichiro Watanabe und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics and Dentofacial Orthopedics, Tokushima University Graduate School of Biomedical Sciences, Tokushima, Japan. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Composite Resins, Incisor, Mandible. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 31 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PATIENTS: This case report presents a minimally invasive approach to replace a missing mandibular lateral incisor using a dual-injection molding technique with flowable composite resins. Integrated with a comprehensive digital workflow, this method achieves a structurally and esthetically biomimetic, bi-layered prosthetic solution. A 34-year-old woman with congenital absence of a mandibular lateral incisor was successfully rehabilitated using a direct composite resin-bonded fixed partial denture (RBFPD). DISCUSSION: Two specialized three-dimensional (3D)-printed flexible indices stabilized by a custom-designed 3D-printed rigid holder were employed to ensure the meticulous injection molding of flowable composite resins formulated to emulate the inherent chromatic gradations between dentin and enamel. The inherent flexibility of the indices, combined with the holder, facilitated accurate and seamless adaptation to the complex morphological features of the dental arch, thereby mitigating the challenges commonly associated with rigid 3D-printed resin indices. CONCLUSIONS: The bilayered direct composite RBFPD using 3D printed flexible indices prepared with a full digital workflow has several advantages over other dental prosthetic solutions, including noninvasiveness, cost-effectiveness, biomimetic esthetics, repairability, and shortened treatment times. Although the initial results are promising, further longitudinal studies with larger patient cohorts are required to confirm the long-term efficacy of this approach.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalComposite ResinsIncisorMandibleHumansAdultFemaleDenture, Partial, Fixed, Resin-BondedAnodontiaBiomimetics

Stichwörter der Autor:innen

Bi-layered restorationDigital workflowDirect composite resin-bonded fixed partial dentureInjection molding techniqueMissing lateral incisor

Substanzen

Composite Resins

Autor:innen und Institutionen

  • Department of Orthodontics and Dentofacial Orthopedics, Tokushima University Graduate School of Biomedical Sciences, Tokushima, Japan.
  • Department of Dental Laboratory, Tokushima University Hospital, Tokushima, Japan.
  • Institute of Dental Medicine, First Faculty of Medicine of the Charles University and General University Hospital in Prague, Prague, Czech Republic.
  • Department of Periodontology, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Department of Oral Medicine, Injection, and Immunity, Harvard School of Dental Medicine, Boston, USA.
  • Department of Regenerative Dental Medicine, Tokushima University Graduate School of Biomedical Sciences, Tokushima, Japan.

Zitieren

APA

Watanabe, K., Tanaka, E., Kamoi, K., Tichy, A., Shiba, T., Yonerakura, K., Nakajima, M., Han, R., & Hosaka, K. (2024). A dual composite resin injection molding technique with 3D-printed flexible indices for biomimetic replacement of a missing mandibular lateral incisor. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_23_00239

Vancouver

Watanabe K, Tanaka E, Kamoi K, Tichy A, Shiba T, Yonerakura K, et al. A dual composite resin injection molding technique with 3D-printed flexible indices for biomimetic replacement of a missing mandibular lateral incisor. Journal of Prosthodontic Research. 2024. doi:10.2186/jpr.jpr_d_23_00239

BibTeX
@article{Watanabe2024,
  author = {Watanabe, Keiichiro and Tanaka, Eiji and Kamoi, Kohei and Tichy, Antonin and Shiba, Takahiko and Yonerakura, Kazuhide and Nakajima, Masatoshi and Han, Ruonan and Hosaka, Keiichi},
  title = {A dual composite resin injection molding technique with 3D-printed flexible indices for biomimetic replacement of a missing mandibular lateral incisor},
  journal = {Journal of Prosthodontic Research},
  year = {2024},
  doi = {10.2186/jpr.jpr_d_23_00239}
}
Kostenlos starten →