EUVIMEDEUVIMED entdecken
Crossref

Effect of the build angle on the accuracy of 3D-printed definitive composite resin crowns, onlays, and laminate veneers: An in vitro study

Samet Atasoy, Sultan Aktuğ Karademir, Onurcan Akgün, Rabia Çoban, Ayşegül Kaya

Journal of Dentistry · 2026

DOI: 10.1016/j.jdent.2026.106937 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Dentistry, 2026. Verfasst von Samet Atasoy und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Faculty of Dentistry, Ordu University, Ordu, Turkey. Electronic address: sametatasoy@odu.edu.tr. Hauptthemen laut MEDLINE: Composite Resins, Dental Veneers, Printing, Three-Dimensional, Crowns. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 36 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

OBJECTIVE: This in vitro study evaluated the effect of the build angle on the accuracy of 3D-printed definitive composite resin crowns, onlays, and laminate veneers. METHODS: Phantom models of a maxillary first premolar, first molar, and central incisor were prepared for crown, onlay, and laminate veneer restorations. The restorations were fabricated using a liquid crystal display (LCD) printer and a definitive composite resin at five build angles (0°, 30°, 45°, 70°, and 90°; n = 15 per group) Trueness and precision were evaluated using root mean square (RMS) values from 3D superimposition analyses of the intaglio, external, and overall surfaces. RESULTS: For the crown restorations, the lowest RMS values were observed at a 45° build angle, whereas the highest values were observed at 90° The build angle did not significantly affect crown precision (P ≥ 0.091). For the onlay and laminate veneer restorations, the lowest RMS values were observed at a 30° build angle, whereas the highest values were observed at 90° Regarding precision, the 30° build angle for the onlays and the 0° and 30° build angles for the laminate veneers resulted in significantly lower RMS values for the external and overall surfaces (P ≤ 0.012). All the RMS values remained below the clinically acceptable threshold of 100 μm. CONCLUSION: The build angle significantly influenced the accuracy of 3D-printed definitive composite resin restorations. The optimal build angle depended on the restoration type, with 45° for crowns and 30° for onlays and laminate veneers. CLINICAL SIGNIFICANCE: Appropriate build angle selection may improve the manufacturing accuracy and clinical fit of 3D-printed definitive composite resin restorations.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsDental VeneersPrinting, Three-DimensionalCrownsDental Prosthesis DesignInlaysHumansDental MaterialsIncisorModels, Dental

Stichwörter der Autor:innen

3D printingAccuracyBuild angleComposite resinCrownsLaminate veneersOnlays

Substanzen

Composite ResinsDental Materials

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Faculty of Dentistry, Ordu University, Ordu, Turkey. Electronic address: sametatasoy@odu.edu.tr.
  • Department of Restorative Dentistry, Faculty of Dentistry, Ordu University, Ordu, Turkey.

Zitieren

APA

Atasoy, S., Aktuğ Karademir, S., Akgün, O., Çoban, R., & Kaya, A. (2026). Effect of the build angle on the accuracy of 3D-printed definitive composite resin crowns, onlays, and laminate veneers: An in vitro study. Journal of Dentistry. https://doi.org/10.1016/j.jdent.2026.106937

Vancouver

Atasoy S, Aktuğ Karademir S, Akgün O, Çoban R, Kaya A. Effect of the build angle on the accuracy of 3D-printed definitive composite resin crowns, onlays, and laminate veneers: An in vitro study. Journal of Dentistry. 2026. doi:10.1016/j.jdent.2026.106937

BibTeX
@article{Atasoy2026,
  author = {Atasoy, Samet and Aktuğ Karademir, Sultan and Akgün, Onurcan and Çoban, Rabia and Kaya, Ayşegül},
  title = {Effect of the build angle on the accuracy of 3D-printed definitive composite resin crowns, onlays, and laminate veneers: An in vitro study},
  journal = {Journal of Dentistry},
  year = {2026},
  doi = {10.1016/j.jdent.2026.106937}
}
Kostenlos starten →