EUVIMEDEUVIMED entdecken
Crossref

Effect of support structures on the trueness and precision of 3D printing dentures: An in vitro study

Sahaprom Namano, Manabu Kanazawa, Awutsadaporn Katheng, Bui Ngoc Huyen Trang, Tamaki Hada, Yuriko Komagamine, Maiko Iwaki, Shunsuke Minakuchi

Journal of Prosthodontic Research · 2024

DOI: 10.2186/jpr.jpr_d_22_00266 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2024. Verfasst von Sahaprom Namano und 7 weiteren Autor:innen. Beteiligte Einrichtung: Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan. Hauptthemen laut MEDLINE: Computer-Aided Design, Printing, Three-Dimensional. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 44 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

Additive manufacturing has revolutionized the fabrication of complete dentures. However, this process involves support structure, which is a construction part that holds the specimen during printing, and may prove to be disadvantageous. Therefore, this in vitro study compared the effect of support structure reduction on various volume and area distributions of a 3D-printed denture base to determine optimal parameters based on accuracy.

Methods

A complete maxillary denture base construction file was used as reference. Twenty denture bases were 3D printed under four conditions (total n=80): no support structure reduction (control), palatal support structure reduction (Condition P), border support structure reduction (Condition B), and palatal and border support structure reduction (Condition PB). Printing time and resin consumption were also recorded. The intaglio surface trueness and precision of all acquired data were exported to a 3D analysis software, and the dimensional changes to the denture base were analyzed using the root-mean-square estimate (RMSE) to assess geometric accuracy and generate color map patterns. Nonparametric Kruskal-Wallis and Steel-Dwass tests (α=0.05) analyzed the accumulated data.

Results

Control had the lowest RMSE values for trueness and precision. Nevertheless, it demonstrated a significantly lower RMSE than that of Condition B (P=0.02) in precision. Owing to negative deviation at the palatal region, Conditions P and PB had higher retention than Control and Condition B regarding the color map pattern.

Conclusions

Within the limitations of this study, the reduction of palatal and border support structures showed optimal accuracy with resource and cost savings.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignPrinting, Three-DimensionalDenture, CompleteMaxillaSoftware

Stichwörter der Autor:innen

3D printingAccuracyDenture baseDigital dentistrySupport structure

Autor:innen und Institutionen

  • Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Digital Dentistry Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Faculty of Dentistry, Naresuan University, Phitsanulok, Thailand.

Zitieren

APA

Namano, S., Kanazawa, M., Katheng, A., Trang, B. N. H., Hada, T., Komagamine, Y., Iwaki, M., & Minakuchi, S. (2024). Effect of support structures on the trueness and precision of 3D printing dentures: An in vitro study. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_22_00266

Vancouver

Namano S, Kanazawa M, Katheng A, Trang BNH, Hada T, Komagamine Y, et al. Effect of support structures on the trueness and precision of 3D printing dentures: An in vitro study. Journal of Prosthodontic Research. 2024. doi:10.2186/jpr.jpr_d_22_00266

BibTeX
@article{Namano2024,
  author = {Namano, Sahaprom and Kanazawa, Manabu and Katheng, Awutsadaporn and Trang, Bui Ngoc Huyen and Hada, Tamaki and Komagamine, Yuriko and Iwaki, Maiko and Minakuchi, Shunsuke},
  title = {Effect of support structures on the trueness and precision of 3D printing dentures: An in vitro study},
  journal = {Journal of Prosthodontic Research},
  year = {2024},
  doi = {10.2186/jpr.jpr_d_22_00266}
}
Kostenlos starten →