Use of open‐source software and photogrammetry in the fabrication of 3D‐printed custom trays for edentulous patients: A technical guide
Journal of Prosthodontics · 2025
DOI: 10.1111/jopr.70035 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Prosthodontics, 2025. Verfasst von João Victor Cunha Cordeiro und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas (UNICAMP), Piracicaba, São Paulo, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Photogrammetry, Software, Denture Design. Die Arbeit nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
A technique is described to obtain a 3D‐printed custom tray for complete dentures through open‐source, free software and additive manufacturing. This approach enables the production of custom trays in a cost‐effective and optimized manner. A three‐dimensional (3D) digital cast is obtained by photogrammetry and later used to design a digital custom tray. Then, the digital custom tray is manufactured by a 3D printer to be used in clinical procedures. This technique is a clean, rapid, and low‐cost alternative to the traditional technique.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas (UNICAMP), Piracicaba, São Paulo, Brazil.
- Department of Dentistry, Federal University of Santa Catarina (UFSC), Florianopolis, Santa Catarina, Brazil.
ORCID-Profile: João Victor Cunha Cordeiro, Lauren Bohner, Fernanda Pretto Zatt, Artur Ferronato Soto, Henrique Souza Dos Santos, Maria Eduarda Broering da Silva, Maurício Malheiros Badaró, Ricardo Armini Caldas
Zitieren
APA
Cordeiro, J. V. C., Bohner, L., Zatt, F. P., Soto, A. F., Dos Santos, H. S., da Silva, M. E. B., Badaró, M. M., & Caldas, R. A. (2025). Use of open‐source software and photogrammetry in the fabrication of 3D‐printed custom trays for edentulous patients: A technical guide. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70035
Vancouver
Cordeiro JVC, Bohner L, Zatt FP, Soto AF, Dos Santos HS, da Silva MEB, et al. Use of open‐source software and photogrammetry in the fabrication of 3D‐printed custom trays for edentulous patients: A technical guide. Journal of Prosthodontics. 2025. doi:10.1111/jopr.70035
BibTeX
@article{Cordeiro2025,
author = {Cordeiro, João Victor Cunha and Bohner, Lauren and Zatt, Fernanda Pretto and Soto, Artur Ferronato and Dos Santos, Henrique Souza and da Silva, Maria Eduarda Broering and Badaró, Maurício Malheiros and Caldas, Ricardo Armini},
title = {Use of open‐source software and photogrammetry in the fabrication of 3D‐printed custom trays for edentulous patients: A technical guide},
journal = {Journal of Prosthodontics},
year = {2025},
doi = {10.1111/jopr.70035}
}
EUVIMED