EUVIMEDEUVIMED entdecken
Crossref

Combination of Laser Additive Manufacturing and Sol-Gel method for bone tissue regeneration silica-based scaffolds

Scano, Alessandra, Siegers, Maik, Petrovic, Marc, S. Weichert, Danka Katrakova‐Krüger, Guido Ennas, Christoph Hartl

Transactions on Additive Manufacturing Meets Medicine · 30.07.2024

DOI: 10.18416/ammm.2024.24091908 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Transactions on Additive Manufacturing Meets Medicine, erschienen am 30.07.2024. Verfasst von Scano und 9 weiteren Autor:innen.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser additive manufacturing (LAM) is an established method to process additively metals and polymers, which is already available at the industrial level [1]. On the contrary, laser treatment implementation of ceramics is still a challenge due to low thermal shock resistance of the material, weak densification during processing, and strongly temperature-dependent absorptance of laser light [2]. Moreover, current manufacturing protocols require the use of polymer bindings to avoid cracks during the drying step [3]. In this work, we present a new polymer binder-free manufacture route for ceramic materials, which combines for first time the advantages of LAM and sol -gel method to obtain silica-based porous scaffolds for bone tissue regeneration. In a typical preparation, fumed silica and carbon nanotubes (CNTs) were dispersed in distilled water and mixed to obtain a sol, which was deposited layer by layer on a copper plate. After, each layer a laser treatment was applied using a Ytterbium fiber laser emitting at 1064 nm, working in a pulsed mode. Cracks free green specimens with a setup dimension of 4 × 4 mm2 were obtained that were then sintered to both consolidate the specimens and eliminate the CNTs. Influence of the laser power and scanning speed as well as of the sintering conditions on the physico-chemical and mechanical properties of the final material were studied by optical and scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, thermal analysis and micro hardness measurements.

Schlagwörter

laser additive manufacturingsol-gel synthesisbone regenerationfumed silicacarbon nanotubesytterbium-doped fiber laserpulsed laser treatmentsinteringporous scaffoldslaser power and scanning speed

Zitieren

APA

Scano, Alessandra, Siegers, Maik, Petrovic, Marc, Weichert, S., Katrakova‐Krüger, D., Ennas, G., & Hartl, C. (2024). Combination of Laser Additive Manufacturing and Sol-Gel method for bone tissue regeneration silica-based scaffolds. Transactions on Additive Manufacturing Meets Medicine. https://doi.org/10.18416/ammm.2024.24091908

Vancouver

Scano, Alessandra, Siegers, Maik, Petrovic, Marc, et al. Combination of Laser Additive Manufacturing and Sol-Gel method for bone tissue regeneration silica-based scaffolds. Transactions on Additive Manufacturing Meets Medicine. 2024. doi:10.18416/ammm.2024.24091908

BibTeX
@article{Scano2024,
  author = {Scano and Alessandra and Siegers and Maik and Petrovic and Marc and Weichert, S. and Katrakova‐Krüger, Danka and Ennas, Guido and Hartl, Christoph},
  title = {Combination of Laser Additive Manufacturing and Sol-Gel method for bone tissue regeneration silica-based scaffolds},
  journal = {Transactions on Additive Manufacturing Meets Medicine},
  year = {2024},
  doi = {10.18416/ammm.2024.24091908}
}
Kostenlos starten →