Bond strength of thermoformed and 3D-printed aligners with universal primer versus one-step aligner adhesive with and without sandblasting: An in vitro study
PLOS One · 23.01.2026 · 21 (1) · e0341664
DOI: 10.1371/journal.pone.0341664 ↗Kurz gefasst
Fachartikel in der Zeitschrift PLOS One, online erschienen am 23.01.2026. Verfasst von Viet Anh Nguyen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics, Faculty of Dentistry, Phenikaa University, Hanoi, Viet Nam. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Adhesives, Dental Bonding. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Objectives
Chairside bonding of auxiliaries directly to aligners can avoid remanufacturing trays, but optimal protocols may be substrate-specific across modern thermoformed and 3D-printed materials. This study aimed to compare bond strength and failure mode across six representative aligner materials using a universal primer-orthodontic adhesive combination and a one-step aligner adhesive, with and without sandblasting. Materials and methods Polyethylene terephthalate glycol-modified (PETG), thermoplastic polyurethane (TPU), and glycol-modified polycyclohexylenedimethylene terephthalate (PCTG), together with three 3D-printed resins (TA-28, TC-85DAC, DCA), were prepared as 0.76-mm plates (n = 64). Specimens received alumina sandblasting or no treatment, then were bonded with either of two bonding strategies (n = 16). After thermocycling, bond strength was tested, and failures were scored by ARI. Two- and three-way ANOVA and proportional-odds modeling assessed effects (α = 0.05).
Results
Bond strength showed significant main effects of material and sandblasting, with significant material–sandblasting and material–primer interactions. The primer main effect was not significant. Post hoc tests confirmed substrate-specific rankings. PETG with Bond Aligner (non-sandblasted) reached 26.71 MPa, while DCA with universal primer (sandblasted) reached 22.36 MPa. Sandblasting generally increased bond strength, with some exceptions. Failure mode was material-dependent and not completely parallel with bond strength.
Conclusions
Bonding efficacy depends on the aligner substrate. For thermoformed trays, a one-step aligner adhesive is preferable, with sandblasting contraindicated for PETG but advantageous for more elastic TPU and PCTG. For 3D-printed trays, a universal primer-orthodontic adhesive combination performs more consistently, with sandblasting benefiting DCA and TA-28, whereas TC-85DAC performs slightly better without it.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Orthodontics, Faculty of Dentistry, Phenikaa University, Hanoi, Viet Nam.
- Department of Orthodontics and Pedodontics, Faculty of Dentistry, Van Lang University, Ho Chi Minh City, Vietnam.
- Private Practice, Viet Anh Orthodontic Clinic, Hanoi, Vietnam.
ORCID-Profile: Viet Anh Nguyen
Zitieren
APA
Nguyen, V. A., Hoang, V., Vuong, T. Q. T., Phung, T. N., & Bich Hoang, N. P. (2026). Bond strength of thermoformed and 3D-printed aligners with universal primer versus one-step aligner adhesive with and without sandblasting: An in vitro study. PLOS One, 21(1), e0341664. https://doi.org/10.1371/journal.pone.0341664
Vancouver
Nguyen VA, Hoang V, Vuong TQT, Phung TN, Bich Hoang NP. Bond strength of thermoformed and 3D-printed aligners with universal primer versus one-step aligner adhesive with and without sandblasting: An in vitro study. PLOS One. 2026;21(1):e0341664. doi:10.1371/journal.pone.0341664
BibTeX
@article{Nguyen2026,
author = {Nguyen, Viet Anh and Hoang, Viet and Vuong, Thi Quynh Trang and Phung, Thi Nga and Bich Hoang, Nghi Phan},
title = {Bond strength of thermoformed and 3D-printed aligners with universal primer versus one-step aligner adhesive with and without sandblasting: An in vitro study},
journal = {PLOS One},
year = {2026},
volume = {21},
number = {1},
pages = {e0341664},
doi = {10.1371/journal.pone.0341664}
}
EUVIMED