EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Computational modeling of residual stress in welded high-strength steel box sections

Yihan Tu, Zhongming Liu iD, Yangsen Tu, Mingqiang Sheng

PLOS One · 2025

DOI: 10.1371/journal.pone.0332445 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, 2025. Verfasst von Yihan Tu und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Information Engineering, Gandong University, Fuzhou, China. Hauptthemen laut MEDLINE: Steel, Welding, Stress, Mechanical, Computer Simulation. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Provincial Higher Education Teaching Reform Research Project of Jiangxi Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the residual stress patterns of welded box-section members constructed from high-strength steel (HSS). A finite element method (FEM) model developed in ANSYS is validated using experimental data from previous studies. Additionally, experimental data are directly utilized in the analysis to reinforce and contextualize numerical outcomes. A comprehensive parametric analysis explores the impact of plate thickness, width-to-thickness ratio, steel strength, welding sequence, and welding conditions on residual stress distributions. The results reveal that tensile residual stresses near weld regions consistently reach 82.6–97.8% of the yield strength and primarily depend on steel strength, with minimal sensitivity to section dimensions. In contrast, compressive residual stresses in mid-panel regions decrease by up to 72.2% with an increase in width-to-thickness ratio from 3.0 to 23.0, and the reduction rate is influenced by plate thickness. Additionally, welding sequences significantly affect residual stress magnitudes without altering their general distribution patterns. Diagonal welding method in the same direction effectively reduces mid-panel compressive stresses by up to 17.0%, and butt welds generate approximately 48.3% lower residual stresses than fillet welds. A residual stress distribution model for HSS welded box sections is developed. The model shows good agreement with experimental data with average deviation within 9.5% and can serve as a simplified yet reliable input for structural design, safety assessment, and advanced finite element modeling of welded steel members.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

SteelWeldingStress, MechanicalComputer SimulationFinite Element AnalysisTensile StrengthCompressive StrengthModels, Theoretical

Substanzen

Steel

Autor:innen und Institutionen

  • School of Information Engineering, Gandong University, Fuzhou, China.
  • Academic Affairs Office, Nanchang Normal College of Applied Technology, Nanchang, China.
  • School of Engineering and Construction, Nanchang University, Nanchang, China.

ORCID-Profile: Zhongming Liu

Förderung

  • National Natural Science Foundation of China
  • Provincial Higher Education Teaching Reform Research Project of Jiangxi Province

Zitieren

APA

Tu, Y., Liu, Z., Tu, Y., & Sheng, M. (2025). Computational modeling of residual stress in welded high-strength steel box sections. PLOS One. https://doi.org/10.1371/journal.pone.0332445

Vancouver

Tu Y, Liu Z, Tu Y, Sheng M. Computational modeling of residual stress in welded high-strength steel box sections. PLOS One. 2025. doi:10.1371/journal.pone.0332445

BibTeX
@article{Tu2025,
  author = {Tu, Yihan and Liu, Zhongming and Tu, Yangsen and Sheng, Mingqiang},
  title = {Computational modeling of residual stress in welded high-strength steel box sections},
  journal = {PLOS One},
  year = {2025},
  doi = {10.1371/journal.pone.0332445}
}
Kostenlos starten →