EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental and numerical investigation of the mechanical performance of natural–synthetic hybrid composite laminates

Shaik Irfan Sadaq iD, Dakuri Vasudev Srividya, Abhishek Agarwal, Balram Yelamasetti, Samera Saniya, Jamyang Choden iD

PLOS One · 2026

DOI: 10.1371/journal.pone.0354203 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, 2026. Verfasst von Shaik Irfan Sadaq und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Muffakham Jah College of Engineering and Technology, Hyderabad, Telangana, India. Hauptthemen laut MEDLINE: Materials Testing, Polymers. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fiber-reinforced polymer composites have attracted considerable attention in engineering applications owing to their high strength-to-weight ratio, corrosion resistance, and tailorable mechanical properties. Hybridization provides an effective approach for combining the advantageous characteristics of different reinforcement materials to achieve improved overall laminate performance. In the present study, three six-ply hybrid composite laminates, namely J2/C2/J2, J2/G2/J2, and C2/G2/C2, with a [0°/90°] stacking sequence and a relatively high fiber content obtained through controlled hand lay-up fabrication, were fabricated using the hand lay-up technique. Test specimens were prepared according to the relevant ASTM standards and subjected to tensile, compressive, and flexural testing. In addition, finite element simulations were performed using ANSYS Mechanical APDL 2020 R1 to validate the experimental observations. The experimental results demonstrated that natural–synthetic fiber hybridization significantly enhanced the mechanical performance of the investigated laminates. The incorporation of carbon fiber into jute-based laminates resulted in an average strength improvement of approximately 88%, whereas glass-fiber incorporation produced an improvement of approximately 55%. Among the investigated configurations, the C2/G2/C2 laminate exhibited the highest tensile strength (approximately 140 MPa), compressive strength (approximately 39 MPa), and flexural strength (approximately 109 MPa). The numerical predictions showed good agreement with the experimental measurements, with maximum deviations below 1.2%. The results confirm the effectiveness of hybridization in enhancing the mechanical response of composite laminates and identify the C2/G2/C2 configuration as the most promising among the investigated laminate systems. These findings demonstrate the influence of natural–synthetic fiber hybridization on laminate mechanical performance and provide useful information for the design of lightweight composite structural components. Further studies involving pressure-vessel fabrication and internal-pressure testing are required before pressure-vessel applications can be established.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Materials TestingPolymersTensile StrengthCompressive StrengthFinite Element AnalysisCarbon FiberStress, MechanicalGlass

Substanzen

Carbon FiberPolymers

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Muffakham Jah College of Engineering and Technology, Hyderabad, Telangana, India.
  • Department of Mechanical Engineering, University College of Engineering, Osmania University, Hyderabad, Telangana, India.
  • Department of Energy Technology, Tallinn University of Technology, Tallinn, Estonia.
  • Department of Mechanical Engineering, Sreyas Institute of Engineering and Technology, Hyderabad, Telangana, India.
  • Department of Physics, Muffakham Jah College of Engineering and Technology, Hyderabad, Telangana, India.
  • Department of Mechanical Engineering, College of Science and Technology, Royal University of Bhutan, Phuentsholing, Bhutan.

ORCID-Profile: Shaik Irfan Sadaq, Jamyang Choden

Zitieren

APA

Sadaq, S. I., Srividya, D. V., Agarwal, A., Yelamasetti, B., Saniya, S., & Choden, J. (2026). Experimental and numerical investigation of the mechanical performance of natural–synthetic hybrid composite laminates. PLOS One. https://doi.org/10.1371/journal.pone.0354203

Vancouver

Sadaq SI, Srividya DV, Agarwal A, Yelamasetti B, Saniya S, Choden J. Experimental and numerical investigation of the mechanical performance of natural–synthetic hybrid composite laminates. PLOS One. 2026. doi:10.1371/journal.pone.0354203

BibTeX
@article{Sadaq2026,
  author = {Sadaq, Shaik Irfan and Srividya, Dakuri Vasudev and Agarwal, Abhishek and Yelamasetti, Balram and Saniya, Samera and Choden, Jamyang},
  title = {Experimental and numerical investigation of the mechanical performance of natural–synthetic hybrid composite laminates},
  journal = {PLOS One},
  year = {2026},
  doi = {10.1371/journal.pone.0354203}
}
Kostenlos starten →