EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experiment study on the cross-layer propagation characteristics of hydraulic fracturing cracks in coal roof rocks

Maolin Yang, Shuai Lv, Xing Wang, Mao Wang, Sicheng Wang, Yu Meng, Yongjiang Luo iD

PLOS One · 03.10.2025 · 20 (10) · e0331970

DOI: 10.1371/journal.pone.0331970 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, online erschienen am 03.10.2025. Verfasst von Maolin Yang und 6 weiteren Autor:innen. Beteiligte Einrichtung: Geotechnical Survey Company, CHN Energy Shendong Coal Group, Shenmu, China. Hauptthemen laut MEDLINE: Coal, Hydraulic Fracking. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fracture of the overlying roof of a coal seam has become the main method to increase the permeability of coal seam in coalbed methane exploitation. Because the fracture must grow into the coal and through any stone layers, the mechanical property difference between the overlying roof rocks and coal inevitably leads to significant changes in the crack propagation behaviors. In this study, an embedded strain sensor with low cost and simple operation is used to measure the strain in laboratory samples representing the coal seam and roof near the interface for fractures initiated in the roof to obtain the width change of the hydraulic fracture at the interface. At the same time, the propagation behavior of hydraulic fractures at the interface is expressed by combining fracture images and pumping pressure. The results show that a larger horizontal stress difference, larger flow rate, lower coal seam modulus, and smaller intermediate layer thickness are beneficial for the propagation of hydraulic fractures from the roof into the coal seam and the activation of the roof-coal interface. On-site hydraulic fracturing design should fully consider the in-situ stress and coal seam modulus, and design reasonable fracturing drilling location and injection flow. The width of hydraulic fracture in coal seam is larger than that in roof, and increases with the modulus of coal and roof approach, which is beneficial to the migration of proppant in roof-coal seam hydraulic fracture. Therefore, the migration of fracturing proppant in an actual coal seam roof is limited by the width of hydraulic fractures in the roof.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CoalHydraulic FrackingStress, MechanicalCoal Mining

Substanzen

Coal

Autor:innen und Institutionen

  • Geotechnical Survey Company, CHN Energy Shendong Coal Group, Shenmu, China.
  • School of Mines, China University of Mining and Technology, Xuzhou, China.
  • CHN Energy Shendong Technology Institute, Shenmu, China.
  • State Key Laboratory of Coal Mine Disaster Dynamics and Control, School of Resources and safety Engineering, Chongqing University, Chongqing, China.

ORCID-Profile: Yongjiang Luo

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Yang, M., Lv, S., Wang, X., Wang, M., Wang, S., Meng, Y., & Luo, Y. (2025). Experiment study on the cross-layer propagation characteristics of hydraulic fracturing cracks in coal roof rocks. PLOS One, 20(10), e0331970. https://doi.org/10.1371/journal.pone.0331970

Vancouver

Yang M, Lv S, Wang X, Wang M, Wang S, Meng Y, et al. Experiment study on the cross-layer propagation characteristics of hydraulic fracturing cracks in coal roof rocks. PLOS One. 2025;20(10):e0331970. doi:10.1371/journal.pone.0331970

BibTeX
@article{Yang2025,
  author = {Yang, Maolin and Lv, Shuai and Wang, Xing and Wang, Mao and Wang, Sicheng and Meng, Yu and Luo, Yongjiang},
  title = {Experiment study on the cross-layer propagation characteristics of hydraulic fracturing cracks in coal roof rocks},
  journal = {PLOS One},
  year = {2025},
  volume = {20},
  number = {10},
  pages = {e0331970},
  doi = {10.1371/journal.pone.0331970}
}
Kostenlos starten →