High-performance energy harvesting and continuous output using nylon-11/BaTiO₃-PVDF triboelectric nanogenerators with strong dielectric properties
PLOS One · 20.05.2025 · 20 (5) · e0319802
DOI: 10.1371/journal.pone.0319802 ↗Kurz gefasst
Fachartikel in der Zeitschrift PLOS One, online erschienen am 20.05.2025. Verfasst von Xiong Dien und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Big Data and Internet of Things, Chongqing Vocational Institute of Engineering, Chongqing, China. Hauptthemen laut MEDLINE: Titanium, Electric Power Supplies, Polyvinyls, Barium Compounds. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation Project of Chongqing Science & Technology Commission, Scientific and Technological Research Program of Chongqing Municipal Education Commission.
Abstract (Originalsprache)
Among various emerging energy technologies, triboelectric nanogenerators (TENGs) have garnered significant attention owing to their ability to convert environmental mechanical energy into electrical energy through the triboelectric effect and electrostatic induction. However, there are some problems with optimizing the electrical output and conversion efficiency of TENGs. This paper presents a high-performance TENG enhanced with BaTiO₃ nanowires(BTONWs) using electrospinning technology. PVDF was doped with BTONWs to fabricate TENGs with high flexibility and efficient energy conversion. BaTiO₃ and PVDF all exhibited inherent properties and triboelectric properties, maximizing the conversion of pressure into electrical energy output. This integration effectively enhances the conversion power and provides a continuous energy supply. Experimental results show that the fabricated TENGs achieved a current and voltage of 12 μA and 280 V, respectively, with a maximum power density of 1.45 W/m 2 at a load resistance of 90 MΩ. In addition, the performance of the TENGs was tested using a calculator, timer, and LED lights. By connecting to a simple external circuit and continuously tapping the TENG, the devices functioned normally, demonstrating that the TENG can constantly and stably output electrical energy by continuously collecting mechanical energy to power microgenerators. This work may significantly contribute to developing energy harvesting, wearable devices, and micropower sources.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- School of Big Data and Internet of Things, Chongqing Vocational Institute of Engineering, Chongqing, China.
- Faculty of Engineering, Built Environment and Information Technology, SEGi University, Kuala Lumpur, Malaysia.
- Chongqing Vocational and Technical University of Mechatronics, Chongqing, China.
- School of Electronic Information Engineering, Geely University of China, Chengdu, China.
ORCID-Profile: Yang Zhuanqing
Förderung
- Natural Science Foundation Project of Chongqing Science & Technology Commission
- Scientific and Technological Research Program of Chongqing Municipal Education Commission
Zitieren
APA
Dien, X., Ramli, N., Thio, T. H. G., Linfeng, C., Lin, Z., Jiang, Y., & Zhuanqing, Y. (2025). High-performance energy harvesting and continuous output using nylon-11/BaTiO₃-PVDF triboelectric nanogenerators with strong dielectric properties. PLOS One, 20(5), e0319802. https://doi.org/10.1371/journal.pone.0319802
Vancouver
Dien X, Ramli N, Thio THG, Linfeng C, Lin Z, Jiang Y, et al. High-performance energy harvesting and continuous output using nylon-11/BaTiO₃-PVDF triboelectric nanogenerators with strong dielectric properties. PLOS One. 2025;20(5):e0319802. doi:10.1371/journal.pone.0319802
BibTeX
@article{Dien2025,
author = {Dien, Xiong and Ramli, Nurulazlina and Thio, Tzer Hwai Gilbert and Linfeng, Cheng and Lin, Zhang and Jiang, Yuan and Zhuanqing, Yang},
title = {High-performance energy harvesting and continuous output using nylon-11/BaTiO₃-PVDF triboelectric nanogenerators with strong dielectric properties},
journal = {PLOS One},
year = {2025},
volume = {20},
number = {5},
pages = {e0319802},
doi = {10.1371/journal.pone.0319802}
}
EUVIMED