EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimizing strength of directly recycled aluminum chip-based parts through a hybrid RSM-GA-ANN approach in sustainable hot forging

Yahya M Altharan iD, Shazarel Shamsudin, Mohd Amri Lajis, Sami Al-Alimi, Nur Kamilah Yusuf, Nayef Abdulwahab Mohammed Alduais, Atef M Ghaleb, Wenbin Zhou

PLOS ONE · 14.03.2024 · 19 (3) · e0300504

DOI: 10.1371/journal.pone.0300504 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, online erschienen am 14.03.2024. Verfasst von Yahya M Altharan und 7 weiteren Autor:innen. Beteiligte Einrichtung: Sustainable Manufacturing and Recycling Technology, Advanced Manufacturing and Materials Center (SMART-AMMC), Universiti Tun Hussein Onn Malaysia, Pa…. Hauptthemen laut MEDLINE: Aluminum, Neural Networks, Computer. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 72 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universiti Tun Hussein Onn Malaysia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Direct recycling of aluminum waste is crucial in sustainable manufacturing to mitigate environmental impact and conserve resources. This work was carried out to study the application of hot press forging (HPF) in recycling AA6061 aluminum chip waste, aiming to optimize operating factors using Response Surface Methodology (RSM), Artificial Neural Network (ANN) and Genetic algorithm (GA) strategy to maximize the strength of recycled parts. The experimental runs were designed using Full factorial and RSM via Minitab 21 software. RSM-ANN models were employed to examine the effect of factors and their interactions on response and to predict output, while GA-RSM and GA-ANN were used for optimization. The chips of different morphology were cold compressed into billet form and then hot forged. The effect of varying forging temperature (Tp, 450–550°C), holding time (HT, 60–120 minutes), and chip surface area to volume ratio (A S :V, 15.4–52.6 mm 2 /mm 3 ) on ultimate tensile strength (UTS) was examined. Maximum UTS (237.4 MPa) was achieved at 550°C, 120 minutes and 15.4 mm 2 /mm 3 of chip’s A S : V. The Tp had the largest contributing effect ratio on the UTS, followed by HT and A S :V according to ANOVA analysis. The proposed optimization process suggested 550°C, 60 minutes, and 15.4 mm 2 as the optimal condition yielding the maximum UTS. The developed models’ evaluation results showed that ANN (with MSE = 1.48%) outperformed RSM model. Overall, the study promotes sustainable production by demonstrating the potential of integrating RSM and ML to optimize complex manufacturing processes and improve product quality.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

AluminumNeural Networks, ComputerTemperatureCold TemperatureSoftware

Substanzen

Aluminum

Autor:innen und Institutionen

  • Sustainable Manufacturing and Recycling Technology, Advanced Manufacturing and Materials Center (SMART-AMMC), Universiti Tun Hussein Onn Malaysia, Parit Raja, Malaysia.
  • Faculty of Computer Science and Information Technology (FSKTM), Universiti Tun Hussein Onn Malaysia (UTHM), Parit Raja, Batu Pahat, Johor, Malaysia.
  • Department of Industrial Engineering, College of Engineering Alfaisal University, Riyadh, Saudi Arabia.
  • School of Science and Engineering, University of Dundee, Dundee, United Kingdom.

ORCID-Profile: Yahya M Altharan

Förderung

  • Universiti Tun Hussein Onn Malaysia

Zitieren

APA

Altharan, Y. M., Shamsudin, S., Lajis, M. A., Al-Alimi, S., Yusuf, N. K., Alduais, N. A. M., Ghaleb, A. M., & Zhou, W. (2024). Optimizing strength of directly recycled aluminum chip-based parts through a hybrid RSM-GA-ANN approach in sustainable hot forging. PLOS ONE, 19(3), e0300504. https://doi.org/10.1371/journal.pone.0300504

Vancouver

Altharan YM, Shamsudin S, Lajis MA, Al-Alimi S, Yusuf NK, Alduais NAM, et al. Optimizing strength of directly recycled aluminum chip-based parts through a hybrid RSM-GA-ANN approach in sustainable hot forging. PLOS ONE. 2024;19(3):e0300504. doi:10.1371/journal.pone.0300504

BibTeX
@article{Altharan2024,
  author = {Altharan, Yahya M and Shamsudin, Shazarel and Lajis, Mohd Amri and Al-Alimi, Sami and Yusuf, Nur Kamilah and Alduais, Nayef Abdulwahab Mohammed and Ghaleb, Atef M and Zhou, Wenbin},
  title = {Optimizing strength of directly recycled aluminum chip-based parts through a hybrid RSM-GA-ANN approach in sustainable hot forging},
  journal = {PLOS ONE},
  year = {2024},
  volume = {19},
  number = {3},
  pages = {e0300504},
  doi = {10.1371/journal.pone.0300504}
}
Kostenlos starten →