EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

The science of printing and polishing 3D printed dentures

Kavishma Sulaya, Swapna B V iD, Vaishnavi M Nayak iD

F1000Research · 06.01.2025 · 13 · 1266

DOI: 10.12688/f1000research.157596.2 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift F1000Research, online erschienen am 06.01.2025. Verfasst von Kavishma Sulaya und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Crown & Bridge, Manipal College of Dental Sciences, Manipal Academy of Higher Education, Manipal, Karnataka, 576104,…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dentures. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To analyze the effectiveness of various techniques available for printing, finishing and polishing of 3D printed prosthesis.

Methods

The articles were selected from electronic databases including PubMed and Scopus. Recently, lot of advancements have been observed in the field of 3D printing in dentistry.

Results

Numerous studies were found explaining the factors affecting the surface roughness such as printing speed, direction, layer thickness, post curing, etc., and the significance in achieving a smooth surface finish of a 3D printed prosthesis. The methods employed to achieve this range, similar to conventional and chairside polishing, are to use advanced coating materials such as light cured glazes to nanoparticles.

Conclusion

3D printing is being used in day-to-day practice and the prosthesis must be aesthetic looking to satisfy the patients’ expectations. There is a lack of data supporting any one polishing method for the prosthesis. There is a need for further research on the existing techniques and newer advancements yielding aesthetic prostheses with an optimal surface finish.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenturesHumansSurface Properties

Stichwörter der Autor:innen

3D printed denturesAdditive manufacturingChairside polishingGlaze materials.Surface roughness

Autor:innen und Institutionen

  • Department of Prosthodontics and Crown & Bridge, Manipal College of Dental Sciences, Manipal Academy of Higher Education, Manipal, Karnataka, 576104, India.

ORCID-Profile: Swapna B V, Vaishnavi M Nayak

Zitieren

APA

Sulaya, K., B V, S., & Nayak, V. M. (2025). The science of printing and polishing 3D printed dentures. F1000Research, 13, 1266. https://doi.org/10.12688/f1000research.157596.2

Vancouver

Sulaya K, B V S, Nayak VM. The science of printing and polishing 3D printed dentures. F1000Research. 2025;13:1266. doi:10.12688/f1000research.157596.2

BibTeX
@article{Sulaya2025,
  author = {Sulaya, Kavishma and B V, Swapna and Nayak, Vaishnavi M},
  title = {The science of printing and polishing 3D printed dentures},
  journal = {F1000Research},
  year = {2025},
  volume = {13},
  pages = {1266},
  doi = {10.12688/f1000research.157596.2}
}
Kostenlos starten →