Recycled PMMA particles from milled discs in denture base materials for improved sustainability
BMC Oral Health · 2025
DOI: 10.1186/s12903-025-05943-1 ↗Kurz gefasst
Fachartikel in der Zeitschrift BMC Oral Health, 2025. Verfasst von Zinab Hijazi und 3 weiteren Autor:innen. Beteiligte Einrichtung: Centre for Dental Sciences, School of Health & Human Sciences, University of Bolton, Bolton, UK. Hauptthemen laut MEDLINE: Polymethyl Methacrylate, Denture Bases, Recycling, Dental Materials. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Objectives
Recycling polymethyl methacrylate (PMMA) in dentistry offers a sustainable solution to address the environmental challenges posed by material waste. This study evaluates the feasibility of incorporating recycled (PMMA) particles into heat-cured denture base materials, focusing on the effects of particle size and concentration on flexural strength, surface hardness, and surface roughness. Material and Methods Recycled PMMA particles, sourced from milling residuals, were classified into fine (< 400 μm) and whole particles and incorporated into virgin PMMA at 10% and 20% weight/weight (w/w) concentrations to form five groups: Control (100% virgin PMMA), Fine 10% (90% virgin PMMA + 10% fine particles), Fine 20% (80% virgin PMMA + 20% fine particles), Whole 10% (90% virgin PMMA + 10% whole particles), and Whole 20% (80% virgin PMMA + 20% whole particles). Flexural strength ( n = 10) was evaluated using a three-point bending test, surface hardness ( n = 10) was assessed using the Vickers hardness test (VHN), and surface roughness ( n = 10) was measured using an optical profilometer. Statistical analysis was performed using two-way ANOVA and Tukey’s post hoc test, with p < 0.05 considered statistically significant.
Results
The results showed that fine particle groups (10% and 20%) maintained flexural strength comparable to the control, whereas whole particle groups exhibited significantly lower values ( p < 0.05). Surface hardness improved in fine particle groups, with the highest value in the 20% fine particle group, whereas whole particles, particularly at 20%, resulted in the lowest hardness ( p < 0.05). Surface roughness remained unaffected across all groups, with values staying within clinically acceptable limits (Ra < 0.2 μm).
Conclusions
These findings suggest that fine recycled PMMA particles can be effectively integrated into denture base materials to maintain or improve specific properties while contributing to sustainability. Clinical Relevance: This study underscores the potential of recycled PMMA as an environmentally friendly alternative, aligning with global sustainability goals in dental material development.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Centre for Dental Sciences, School of Health & Human Sciences, University of Bolton, Bolton, UK.
- Restorative Dentistry, Oman Dental College, Muscat, Oman. aqutieshat@dundee.ac.uk.
- Restorative Dentistry & Dental Biomaterials, Dundee Dental Hospital & School, University of Dundee, Dundee, UK. aqutieshat@dundee.ac.uk.
Zitieren
APA
Hijazi, Z., Qutieshat, A., Nlemorisa, C., & Salem, A. (2025). Recycled PMMA particles from milled discs in denture base materials for improved sustainability. BMC Oral Health. https://doi.org/10.1186/s12903-025-05943-1
Vancouver
Hijazi Z, Qutieshat A, Nlemorisa C, Salem A. Recycled PMMA particles from milled discs in denture base materials for improved sustainability. BMC Oral Health. 2025. doi:10.1186/s12903-025-05943-1
BibTeX
@article{Hijazi2025,
author = {Hijazi, Zinab and Qutieshat, Abubaker and Nlemorisa, Chibuzo and Salem, Abdurahman},
title = {Recycled PMMA particles from milled discs in denture base materials for improved sustainability},
journal = {BMC Oral Health},
year = {2025},
doi = {10.1186/s12903-025-05943-1}
}
EUVIMED